3. Saturated steam at 2 MPa is contained in a piston- cylinder arrangement as shown in the sketch. The initial volume is 0.25 m. Heat is removed from the steam during a quasi-static, constant-pressure process such that 197.6 kJ of work is done by the surroundings on the steam. Determine the quality of the steam at the final state.

3. Saturated steam at 2 MPa is contained in a piston- cylinder arrangement as shown in the sketch. The initial volume is 0.25 m. Heat is removed from the steam during a quasi-static, constant-pressure process such that 197.6 kJ of work is done by the surroundings on the steam. Determine the quality of the steam at the final state.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 300 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.7 m'/kg. Water Heat Figure Qlb i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
Saturated water mixture in a piston cylinder arrangement is initially at 200 oC with a qualityof 50%. The mixture loses heat to the surrounding and contracts isothermally to half of theinitial volume.a- What is the final pressure and the specific work done during the process?b- Draw the process on P-v diagram.
(b) A frictionless piston-cylinder device as shown in Fig. Qlb contains water at 400 kPa and the water is heated at constant pressure from saturated liquid to saturated vapor. Then, the heating process is continued in an isobaric manner until its specific volume reaches the value of 0.5 m²/kg. Water Heat Figure Q1b i) What is the initial temperature of water in the cylinder? ii) What is the final temperature of water in the cylinder? iii) Calculate the total boundary work during the processes, kJ/kg. iv) Calculate the total amount of heat transferred during the processes, kJ/kg. v) Sketch both processes on a T – v diagram with respect to saturation lines.
Mr Luda wants to understand further about a newly created gas. The gas is initiallyat a pressure of 90 kPa, volume of 1.258 m3 and temperature of 10°C (State 1).The gas undergoes a 3-step process in which it is first compressed isothermally toa pressure of 400 kPa and volume of 0.283 m3 (State 2), then expanded at constantpressure back to its original volume (State 3). Finally, the gas is returned to itsoriginal State 1 by cooling at constant volume.a) Sketch the cycle of this system on a P – V diagram.b) Calculate the work done (in kJ) for each process step.c) Determine the total work done for the three-process cycle.d) State whether the work done is on or by the system.
2. Saturated liquid water at 250 kPa is contained in a piston-cylinder device as shown in the figure below. The total initial volume is 0.012m'. As the water is heated, the pressure inside the cylinder remains constant until the piston hits the stops. When the piston hits the stops the specific volume is 0.47443 m/kg. Heat transfer to the water continues until the pressure doubles. NOTE: If needed use the closest value in tables 3 to avoid interpolation. Use 5 decimal digits when using specific volume. a.) Plot the process in a P-v-diagram with respect to saturations lines. b.) Fill de table below c.) Determine the total mass P(kPa) T(°C) v(m'/kg) h(kJ/kg) Phase 2 3.
Ammonia at 0°C with a quality of 60% is containedin a rigid 200-L tank. The tank and ammonia arenow heated to a final pressure of 1 MPa. Determinethe heat transfer for the process.
Q.2 a) 5 kg of air undergoes the cyclic process as shown in the figure. Determine the total work done in joules. (3, 8) Isothermal P, bar Adiabatie. (6, --) V, m³
A copper calorimeter can with mass 0.446kg contains 0.095kg of ice. The system is initially at 0.0oC. (a) if 0.035kg of steam at 100oC and 1.00atm pressure is added to the can, what is the final temperature of the calorimeter can and its contents? (b) at the final temperature, how many kilograms are there of ice, how many of liquid water, and how many of steam?
QUESTIOΝ 1: A piston-cylinder arrangement contains 2 kg of steam originally at 200°C and x-0.9. The volume triples while thc temperature is held coustant. Pieten Calculate: (a) the linal pressure, in MPa, 7=200 C (c) the change in intermal energy, in kl.
A rigid tank (0.010 m³) contains saturated liquid water at 160 deg C. How much heat (kJ) must be added for the pressure to be 800 kPa and a temperature of 200 deg C?
1) A piston-cylinder assembly contains 10 kg of refrigerant 134a. Initially, 8 kg of SA134a is in the liquid phase and the temperature is -10°C. Then there is a slow heat transfer to SA-134a, the piston rises and the piston touches the stoppers when the volume is 400 liters. (a) Show the phase change in the P-V diagram, (b) the temperature of the system at the moment the piston contacts the stoppers, (c) calculate the work done during the process.
1. A frictionless piston-cylinder device with cross-section area of 0.01 m² contains 0.5 m3 gaseous ammonia initially at 200 kPa and 135 °C. Now the gas is isothermally compressed until the pressure increases to 800 psig. The surrounding pressure is 100 kPa and the gravitational force is 9.8 m/s? a. What is the mass of the gas in kg b. What is the mass of the piston in kg c. Calculate the volume in m³ of the compressed gas