3. Modified Design #3 by increasing the cantilever base dimension Increase the dimension of the base from 30 mm to 40 mm C 25- d12 R 40 R6 30 d12 R 125 only need Answer to question #3 - Submit a Report of your results sith discussion & conclusion

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: Is/ are graphical representation of arrangement of geological and structural features of a…

A:

Q: kindly resolve or recheck. thank you

A: Given data:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: Can you help me figure out the different symbols and how many of them are there and put them in…

A: Single Pole Switch Duplex Outlet Quadruplex Outlet Electrical Outlet Fan Outlet Wall Mounted…

Q: Is there any simpler way to got AY,AX,BY,BX?

A: This question is related to the Structural analysis from Civil Engineering.

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: discussfineness modulus

A:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: A frame ABCDE is subjected to forces Po, Pe, and a moment Mcas shown in the Figure below. If Po = 10…

A:

Q: can you please explain your calculations? Im not sure on how you got 2 for the first part

A: Given: The velocity distribution in the boundary layer is given by the expression: uU=1-exp-2×yδ The…

Q: Q3. Determine the plastic moment Mp of the cross sections shown, assuming the material to be…

A:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: (Figure 1) Express your answer with the appropriate 0 Submit μA 6 a 1₂= 26.268 108 mm Previous…

A:

Q: Differentiate force system based on line of action.

A: A force is a push or pull on an object caused by its interaction with another object.

Q: but I nee

A: Draw the figure Consider a differential element of size dy

Q: R10 30 50 O. 15 R30

A:

Q: Q2- Explain how to find the centroid of the area shown in figure y a a 2а За За MATHalino.com

A: Centroid: The imaginary point at which the total area of the system or body is assumed to be…

Q: Find the centroid of square from bottom of X axis having dimension 8 mm *8 mm

A:

Q: order (D^2+4)y

A: Given:- (D^2+4)y=sin x To find:- reduction of order

Q: "hat is the degree of indeterminacy of the given Tucture? a. -1 b. 0 С. 1 d. 2

A:

Q: (1) a L₁ B P b C L2 C D

A:

Q: 1-2. Represent each of the following combinations of units in the correct SI form using an…

A: Nμm

Q: 4" 12" 9 2" 6 (a)

A: Given  Figure with dimensions in  inches .

Q: Mark the correct definition - Measurement is a process of determining the value or the magnitude of…

A: Measurement is the process of measuring any value with respect to the standard value. This process…

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Consider the diagram as shown below. Now. And,

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: where did you get the 3.6 that you divided in v?

A:

Q: Define matrix's diagonal, off-diagonal, subdiagonal, and superdiagonal elements. Illustrate each.

A: An n×n matrix, or a matrix with the same number of columns as rows, is known as a square matrix.

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: Find the solution of the differential equation = A. y = x B. y=x-x* C. y = √x-x4 D. y=x-1 E. Not in…

A: The given differential equation, dydx=2y4+x4xy3 To find the solution of differential equation.

Q: What are mass or weight properties?

A:

Q: Convert 0.0351 to engineering notation. O a) 35.1 × 103 O b) 3.51 × 10–2 )c) 3.51 x 10² O d) 35.1 ×…

A: Solution:- We have to convert the given number into the engineering notation, The given number is…

Q: 112 тm К30 тm ->- 30 тm -+30 тm ->-30 mт -> Рart a) Determine the moment of inertia of the shaded…

A:

Q: sanitary engineering  solve by hardy Cross method  k=8*f*L/pi*g*D^5 f=0.02 g=9.81 pi=e.14

A: Given data in question  Length of pipe  Diameter of pipe Constant value of f Acceleration due to…

Q: 100 N 100 N 100 100 150 250

A:

Q: Y

A:

Q: Where do I get Ix from?

A: Bending stress formula:or, M/ = Z  {here, Z = I/y}or, Z= = 1.376 x 106 mm3W 18 x 50 has Z = 1.557 x…

Open Channel Flow

Open channel flow is a branch of fluid mechanics. It deals with the flow of fluid in an open conduit or free surface. In an open channel flow, gravity induces the flow of water whose surface is open to the air. This flow is free-falling rather than confined in rigid body conduits. The open channel flow depends upon two parameters that are the cross-section of the conduit and the velocity profile. Practical examples of open channel flow are streams, rivers, canals, and other drainage systems.In open channel flow, the cross-sectional area of at least one of the sides is exposed to air, and the surface of water faces atmospheric pressure. This flow is also known as free gravity flow. The cross-sectional area of the conduit can be either man-made or a natural channel. For instance, the flow in rivers and streams are natural conduits, and the flow in a canal and sanitary systems are man-made or engineered channels.