3. For the beam and loading shown in Figure 3: a) Determine the reaction forces at the supports b) Draw the shear force diagram. c) Draw the bending moment diagram. d) Determine the maximum absolute shear and bending moments. A 48 KN су 60 KN DV -1.5 m--1.5 m- Clearly show your steps of calculations. 0.6 m 60 KN E 0.9 m B Figure 3: Beam with concentrated loading.

3. For the beam and loading shown in Figure 3: a) Determine the reaction forces at the supports b) Draw the shear force diagram. c) Draw the bending moment diagram. d) Determine the maximum absolute shear and bending moments. A 48 KN су 60 KN DV -1.5 m--1.5 m- Clearly show your steps of calculations. 0.6 m 60 KN E 0.9 m B Figure 3: Beam with concentrated loading.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
QB4 BENDING STRESS The beam is loaded by one couple at each of its ends, the beam cross-section shown below (Figure QB4). Determine: a) The position of the horizontal neutral axis. b) The second moment of area of the section about the horizontal neutral axis. c) The values of the maximum tensile stress and the maximum compressive stress in the beam if it supports a maximum bending moment of 1200x10 N.mm and the base face is in tension. 150mm 50mm 250mm +50mm I 50mm 150mm Fig QB4
Q1/ A thin-walled cantilever has a constant cross-section of uniform thickness with the dimensions shown in Figure. It is subjected to a system of point loads acting in the planes of the walls of the section in the directions shown. Calculate the direct stresses according to the basic theory of bending at the points 1,2 and 3 of the cross-section at the built-in end along the beam. 50N 2 mm 50 N 80N 2 mm 100 mm 2 36 mm 80 mm 24 mm
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
The cantilever beam (of type w8 × 15) made of A36 steel alloy has a depth d = 8.11 in, as shown below. The moment of inertia I, is 48.0 in.“. 1, 400 lb |1, 400 lb 100 lb/ft d -5 ft- -5 ft- (a) Determine the maximum internal bending moment produced by the loading con- dition provided. (b) Determine the maximum normal stress, due to the bending mo- ment, and the corresponding factor of safety (using o y as the failure stress). (c) Draw a graph that shows the stress in the beam along the y-direction at the point chosen in part (a). (d) Calculate emax based on your answer to part (b). (e) Calculate the radius of curvature p based on your answer to part (d). (a) 26 kip-ft (you should find reaction force of 3.8 kip); (b) 26.4 ksi, 1.38; (c) o(y) = 6.5 у ksi; (d) 9.10(10 4); (е) 372 ft
2. A simple steel beam is to carry the concentrated loads as shown in the figure. (a) Drav the shear diagram, (b) determine the maximum moment, and (c) determine the wide-flange shape that should be used from the list shown if the allowable normal stress for the grade of steel to be used is 110 MPa 60 KN/m 60 KN/m A B 4 m 1m2 m Shape W310x129 S (cm') 1955 Shape W310x202 S (cm) 5049 3423 W310x143 2155 W310x226 W310x158 2565 W310x253 3853 W310x179 2675 W510x285 4311
In structural practice, steel clip angles are commonly used to transfer loads from horizontal girders to verticalcolumns. If the reaction of the girder upon the angle is a downward force of 45 kN as shown in Fig. 2-16 and iftwo 22-mm-diameter rivets resist this force, find the average shearing stress in each of the rivets. As in Problem2.5, assume that the rivet fills the hole.
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx = 25 W 450mm 150mm N.A Son S0mm fig. (B)
w that will not exceed a flexural stress of 14 MN/m or a shearing stress box beam with the given dimensions. Determine the maximum value of The distributed load shown in Fig. P-588 is supported by a nly 588. a of 1.2 MN/m2. -300mm w N/m 250 mm 150 mm 1 m 2 m- 200 mm R2 R1 Flgure P-588. 1.
Determine the maximum tensile bending stresses in the beam shown. LetP= %3D 19 Note Answer in whole number I = 100 × 106 mm4 P kN/m 2. NA 130 mm 6 m B = 4P 200 mm 2P kN 6-X= Am 4P : - GP
Problem 3-31 P + (ks) given: The lap joint is connected together using a 1.25-in.-diameter bolt. the bolt is made from a material having a shear stress-strain diagram that is approximated as shown, P 75 61.1_ 0.05 y (rad) Required: Determine the permanent shear strain in the shear plane of the bolt when an applied force of P = 150 kip is removed.