3. Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following: a. Calculate the tension of the cable. b. Determine the diameter of the wire if the allowable stress is 125 MPa. c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.

3. Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following: a. Calculate the tension of the cable. b. Determine the diameter of the wire if the allowable stress is 125 MPa. c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 100mm 150 mm B. 125 mm 200m 3KN

A: Given: A rigid link supported by a pin at A and two steel wires for wire C with cross sectional area…

Q: Answer

Q: Three cables having an area of 0.05 in? each is carrying the load W as shown. With no stress, the…

A: Given, A = 0.05 in2 E = 29000 ksi

Q: Q/ Determine the forces at the pin joint (F) and the roller support (G) ? 30KN 20KN 4 2m 32m D 2m E…

Q: s. Determine the tension in each wire.

Q: Question 3: calculate the forces in all the members of Cable R = Last two digit of Roll No. S 2.74 m…

Q: R-1.6 A steel plate weighing 27 kN is hoisted by a cable sling that has a clevis at each end. The…

A: W=27kN d=22mm

Q: A frame ACD is supported by ball-and-socket joints at A and D and by a cable that passes through a…

Q: res plate if the allowa and the plates is

Q: *2-8 Part of a control linkage for an a rigid member CBD and a flexible cab applied to the end D of…

Q: has a diameter of 40 mm and 24 mm, respectively. A horizontal member AC carries a linearly…

A: Equilibrium Condition is applied . Shear stress = shear force / Area Tensile force in steel cable…

Q: Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE

A: It is given that :

Q: The cable will fail when subjected to a tension of T = 6 kN. Figure 1) gure 0.1'm -0.75 m- ... * 0.5…

A: Reference : Mechanics, Tension in pulley and cable. Given : A Tension T = 6 KN P force acting…

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each

Q: Q-A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given Internal diameter Di = 40 mm Outer Diameter Do =100 mm Number of revolution per minute N = 120…

Q: For the frame shown below: a) Determine its support reactions, b) Draw the shear force diagram and…

Q: 2. Determine the resultant R of the three tension forces on the eye bolt. 250N 30° देस của vua 300 N…

A: Reference : Engineering Mechanics, Resultant of three tension forces Given : A eye bolt with number…

Q: The column is used to support the upper floor. If a force F = 80 N is applied perpendicular to the…

A: Given data:

Q: The idealize model for suspension bridge is shown in the figure. The truss are pin connected at a,…

A: We have to determine the design diameter of the cable if the allowable tensile stress is 150 MPa and…

Q: 7. Consider the section shown. a=140 mm, b=410 mm, c=360 mm Calculate the following: 12 mm 12 mm a…

Q: 1) If the radius of cables AB and CD are 5mm and modulus of elasticity is 20GPA, calculate the…

A: It is asked to find normal stress and normal strain in cable AB & CD.

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

Q: THE IDEALIZE MODEL FOR SUSPENSION BRIDGE IS SHOWN IN THE FIGURE. THE TRUSS ARE PIN CONNECTED AT A,…

A: Given, Allowable tensile stress σmax=150 MPa Required, Design diameter of cable

Q: PROBLEM 3: CATENARY CABLE An 800 m cable weighing 30N/m is supported at ends that are 100 m…

Q: A SIGN OF UNIFORM DENSITY WEIGHS 1200-N AND IS SUPPORTED BY A BALL AND SOCKET JOINT AT A BY TWO…

Q: Determine the maximum safe load P that can be supported by the bolted connection as shown if the…

A: The values and figure given in the question are as follows: Maximum allowable shear stress in any…

Q: Each of the four vertical links has an 8 x 36-mm uniform rectangular cross section and each of the…

A: To determine: average shearing stress in pin at B average bearing stress at B in member BD average…

Q: 4.4 A 50-lb block is supported by a pin support and a flexible cable, as shown. Draw the free-body…

A: A 50 lb block is supported by a pin support and a flexible cableTo Draw- Free body diagram for the…

Q: Consider the truss structure and the loading given below. a) Compute the average axial stress on…

A: Take equillibrium at point B to find force

Q: thickness "t" of the steel plate if the

Q: 6. Determine the horizontal and vertical components of force which the pins at B, and C exert on…

Q: largest load P that can be applied i cirod

Q: Two separate cables AC and BC support asign structure of weight W = 1575 lb attached to abuilding.…

A: Given:- W = 1575 lb To find:- (a) Find the tension in each cable. Neglect the mass of the cables.(b)…

Q: -2.4 m-t- 6m -2.4m- 1. For the electric transmission tower shown, 1.2 m a. Determine if the truss is…

A: A electric transmission tower is given in the question supported on hinge support at both the ends.…

Q: Three cables are connected at A, where the forces P and Q are applied as shown. Knowing that Q = 10…

A: Given: Required: Value of P

Q: The uniform cable weighing 11.25 N/m is suspended from points A and B. The force in the cable at B…

A: The cable is a structural member used to support load between two supports. The cable transmits…

Q: The homogeneous bar AB weighing 1800 b is supported at either end by a steel cable. Calculate the…

Q: The uniform square plate is suspended by three equal-length cables as shown. Determine the tension T…

A: GIVEN: The uniform square plate is suspended by three equal-length cables. TO CALCULATE: The…

Question

3. Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding
of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment
point is 4m above it, determine the following:
a. Calculate the tension of the cable.
b. Determine the diameter of the wire if the allowable stress is 125 MPa.
c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.
d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Trending now

This is a popular solution!

Step by step

Solved in 7 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q.1. (35%) Cable DB supports canopy beam OABC as shown in the figure. a) Find the required cross-sectional area of cable BD if the allowable normal stress is 200MPa. Je 1.5 m - P=25 kN b) Determine the required diameter of the pins at O if the 2.5 m allowable stress in shear is 120MP.. (Hint: use resultant 1.5 m- 1.5 m- force at O and The pin at O is in double shear.) A c) Determine the elongation and strain of the cable DB if 2.25 m E=180Gpa. (Consider the area of the cable DB as it is calculated in part (a)) Assume that canopy beam weight is W=11KN.
1. From the truss loaded as shown, determine the stress induced on each of the members BC, BD and CD. Consider each member has a cross sectional area of 1200 sq. millimeters. Consider the pulley to be frictionless. Solve the required forces using method of joint and method of sections. 110 kN 5 kN 10 kN 2m 4m 2m E 3m 2m 20KN
• The cable shown supports a girder which weighs 35kN/m. Determine the minimum and maximum tensile forces acting in the cable 1- 30m T 4m L
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
Refer to the figure below. Diagonals BG, CF, CH, and DG are flexible cables. G 1.5 kN 3 m A 3 m 3 m 2.25 m 2.25 m 1 kN E A. Determine the force in member AF. B. Find the force in member GH. C. Compute for the force in cable FC.
Please help me with this one.
Two horizontal 5.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 1.01-in. diameter is used at each connection,determine the bearing stress (in psi) at Bin member AB.
Forces are applied at points A and B of the solid cast-iron bracket shown. Knowing that the bracket has a diameter of 0.8 in., determine the principal stresses and the maxi- mum shearing stress at (a) point H, (b) point K. 1 in. H. K 2500 lb В 3.5 in. 2.5 in. A 600 lb