3. Derive the equation of motion and find the steady-state response of the system depicted in the following figure for rotational motion about the hinge O for the following data: k₁=k₂ = 5000 N/m, a 0.25 m, b=0.5 m, 1-1 m, m= 10 kg, M-50 kg, Fo=500 N, and co= 1000 rpm. wwwwwww Uniform rigid bar, mass m 1-a+7 remet F(t)= Fo sin cot M

3. Derive the equation of motion and find the steady-state response of the system depicted in the following figure for rotational motion about the hinge O for the following data: k₁=k₂ = 5000 N/m, a 0.25 m, b=0.5 m, 1-1 m, m= 10 kg, M-50 kg, Fo=500 N, and co= 1000 rpm. wwwwwww Uniform rigid bar, mass m 1-a+7 remet F(t)= Fo sin cot M

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Beam loaded as shown in Fig. below. Determine the Following: Reaction support at point B. a. 56KN (Downward Direction) b. 56KN (Upward Direction) c. 35KN (Downward Direction) d. 35KN (Upward Direction) Reaction support at point D. a. 26 KN (Downward Direction) b. 26 KN (Upward Direction) c. 24KN (Downward Direction) d. 24KN (Upward Direction) Shear force equation of section AB. a. -30KN b. 30KN c. -32KN d. 32KN Shear force equation of section CD. a. -24KN b. 24KN c. -28KN d. 28KN Bending moment equation of section BC. a. 26KN(x)+56KN.m b. 26KN(x)-56KN.m c. -26KN(x)+56KN.m d. None of the above. Maximum bending moment of the beam. a. 47KN.m b. 46KN.m c. 48KN.m d. None of the above
aragraph v F 1 Normal 1 No Spac... Heading 1 Heading 2 85.00 50.00 25.00 A blanking operation is to be performed to create the part shown below out of 2-mm thick half- hard 405 stainless steel. Provide (a) a drawing showing the punch dimensions; (b) a drawing showing the die dimensions; (c) the blanking force necessary. Note: you will need to translate tensile strength to shear based on the conversion from the text and use material properties from the text as well, tensile strength of 405 can be found in Ch. 6 (Metals). All dimensions noted below are in mm. hp 25.00 T Title 25.00 Subtitle Subtle Em... Emphasis DI Styles
Q3 A) A shaft with 150mm in diameter and 1 m length is to be turned in an engine lathe. Cutting condition are v=2.75 m/s, f=0.3mm/rev, and d=2mm. Determine cutting time and metal removal rate. B) estimate the hot forming temp. for aluminum has a melting point 660°C
Question # 4 A cup of height h=30 mm and diameter d = 50 mm is to be drawn from a steel sheet of 2 mm thickness. a) Calculate the blank diameter Db. b) The Drawing ratio (DR). c) The shearing force needed to cut this blank if the shear strength of the steel sheet is S=180 N/mm2
23- Complete the sentence with the appropriate terminology. In .. a simple punch and die that each have the included angle are used to bend the part. wrinkling b) tearing edge bending V-bending e) earing
16)
Fill in the blanks.(Manufacturing) Thanks in advance
Q3 A) A shaft with 150mm in diameter and I m length is to be turned in an engine lathe. Cutting condition are v-2.75 m/s, f-0.3mm/rev, and d=2mm. Determine cutting time and metal removal rate. B) estimate the hot forming temp. for aluminum has a melting point 660°C
Angle of twist is . . to shear modulus. a. not related with O b. directly proportional c. inverse proportional d. exponentially proportional