3. An empty 100-L tank is connected to a line flowing air (an ideal gas) at 300 K and 6 MPa. The valve is opened and the air starts to flow into the tank. The valve is closed when the pressure inside reaches 5 MPa. This filling process occurs so fast that it can be assumed as adiabatic (i.e., no heat transfer). At the point when the valve is closed, what is the temperature and mass of air inside the tank?

3. An empty 100-L tank is connected to a line flowing air (an ideal gas) at 300 K and 6 MPa. The valve is opened and the air starts to flow into the tank. The valve is closed when the pressure inside reaches 5 MPa. This filling process occurs so fast that it can be assumed as adiabatic (i.e., no heat transfer). At the point when the valve is closed, what is the temperature and mass of air inside the tank?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A tank of compressed air is at 40°C and 10 atm. 1 third of the gas is removed for inflating a car tire. The tank is allowed to exchange heat with the surroundings to maintain its temperature at all times. What kind of a process is this? What is the pressure remaining in the tank? a. Sketch the problem. b.Draw lines identifying the control volume, or control mass. c.Identify the states with numbers, letters, or descriptions such as “in” and “out”. d.Write down the knowns and unknowns. e.Identify what is being asked for. f.State all assumptions.
1. An ideal gas with R = BTU 0.062- and Cy =0.158 BTU undergoes a three Ibm-°R process cycle in aclosed system. From the initial state of 20 psia and 570 °R, the gas is compressed at constant temperature to 1/5 of its initial volume, process 1-2; it is then heated isochorically to state 3,process 2-3; and finally, it expands polytropically with index n= 1.5 back to its initial state, process 3-1. Determine the pressures, specific volumes and temperatures at eardinal points around the cycle and the cycle thermal efficiency.
(a) An elastic balloon behaves such that pressure is proportional to diameter and the balloon contains 0.5 kg air at 200 kPa and 30°C. The balloon is momentarily connected to an air line at 500 kPa and 100°C. Air is let in until the volume doubles, during which process there is a heat transfer of 50 kJ out of the balloon. Find the final temperature and the mass of air that enters the balloon.
(Q4) Two rigid tanks are connected by a valve. Tank A contains 0.2 m' of water at 400 kPa and 3 H,0 H,0 80 percent quality. Tank B contains 0.5 m of water at 200 kPa and 250°C. The valve is now 400kPa 200 kPa opened, and the two tanks eventually come to the o. same state. Determine the pressure and the amount of heat transfer when the system reaches thermal equilibrium with the surroundings at 25°C. B
Saturated moist air enters a heating coil at temperature 400F and exit the coil at 1100F . The amount of moist air entering the heating coil is 25000 CFM .Find the amount of heat addition in Btu/min .
E.2) A paint shop compressor has a storage tank for compressed air with a volume of 1 m³. It initially contains air at 1 MPa and 400 K. The feed valve is opened and air flows into the tank until the pressure reaches 5 MPa and the inside temperature is 450 K. At that time the valve closes. Determine the amount of air that was introduced into the tank. Finally, after the tank cools down, it reaches a room temperature of 300 K. Determine the air pressure at that condition.
A mass of an ideal gas has initial temperature of 160C .If the temperature is raised to 2800C.Find the change of internal energy and enthalpy.Assume the specific heat at constant pressure=1.065 KJ/KgK and specific heat at constant volume= 0.718 KJ/KgK.
the initial mass (m1) in (kg) is A rigid 0.15 m³ tank contains air at 0.8 MPa, 200°C. A valve on the tank is now opened and air flows out until the pressure drops to 100 kPa. During this process, heat is transferred between tank and surrounding, such that when the valve is closed, the temperature inside the tank is 60°C. me valve Tank Air, V-0.15 m² P₁=0.8 MPa, T₁= 200 C P₂ = 100 kPa > T₂ = 60°C
With 3% moisture, 2.5 kg of steam has an enthalpy of 6,600 kJ. It is heated at constant pressure to a finalcondition of 80superheat. Find (a) the pressure of the process and (b) the quantity of heat received by the steam.
3. A polytropic process of air from 150 psia, 300 F, and 1 ft occurs to P2 =20 psia in accordance with PV3 = C. Determine: a. Tz and V2 b. Δυ, ΔΗ, Δs c. SVdp and -S Vdp d. Compute the heat from the polytropic heat and check by the equation Q= Au+S Vdp е. Find the nonflow work and f. The steady flow work for AK=0
3.An adiabatic rigid steam tank has expansion valve. Initially, steam is at 1MPA and 350C Suddenly, the expansion valve was opened until the tank became empty. If the temperature of steam flowing in the expansion valve is 300C, find the pressure in the valve.
1 kg of steam at initial conditions of 5.1 MPa and 370 °C expands in a turbine until it becomes saturated. It is withdrawn and reheated to 340°C. After further expansion in the turbine to 160 , part of the steam is extracted for feedwater heating. The remaining steam expands to the condenser pressure of 0.018 MPa. For 1kg of steam, find Wnet, Ec, Ee and the ideal steam rate. Remember:1. For values taken from the steam tables: Use them as is, do not round off.2. For values obtained by interpolation and final answers obtained by solving, use FOUR (4) decimal places.PLEASE USE THE STEAM TABLE PROVIDED: https://docs.google.com/document/d/1crebk95lXFEAR5d6Y6LymXJNraO9WLgtNjquSlVOvVs/edit