3.- A swimming pool has a partial filtration system, the water whose temperature is 75 °F, is pumped into the swimming pool according to the system shown. The pump discharges 30 GPM, at 60 PSIG. The pipe is made of galvanized steel (E/D=0.001). The pressure loss through the filter is given by the equation AP= 0.6Q², where AP= PSI and Q = GPM. Determine the flow through each branch. 40 ft 60 ft 10 ft FILTER 60 ft 200 ft 60 ft PATM 11.3 lb/in²

3.- A swimming pool has a partial filtration system, the water whose temperature is 75 °F, is pumped into the swimming pool according to the system shown. The pump discharges 30 GPM, at 60 PSIG. The pipe is made of galvanized steel (E/D=0.001). The pressure loss through the filter is given by the equation AP= 0.6Q², where AP= PSI and Q = GPM. Determine the flow through each branch. 40 ft 60 ft 10 ft FILTER 60 ft 200 ft 60 ft PATM 11.3 lb/in²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Estimate the volume flow rate (gpm) in the pipe with a diameter of 50mm and a water velocity of 50m/s. 2. Determine the specific weight of air when the temperature is 1000F and the absolute pressure is 80psi.
4.32 ft 24.5 ft 7.47 ft O Air at 29.4 psig pump A pump delivers water from a lake into a 6 ft diameter by 10 foot tall sealed pressurized tank through 4 inch pipes using a 4.0 horsepower pump with an efficiency of 62%. If the head loss through the system is 6.42 ft, determine the delivery rate (m3/s) of water to the tank, for the tank level and pump pressure shown in the drawing.
Given the 0.063 m length of the syringe. F=1N a. provide an equation to calculate its water flow rate if water is going to travel from a 0.063 m length of syringe with dextrose tube length of 0.5 meter to another 0.063 m syringe (see attached photo). The Inner diameter of the syringe is 0.02. While the inner diameter of dextrose tube is 0.003. b. provide an equation in order to calculate the maximum force or pressure that exerts in plunger in order to travel the water at its maximum speed.
a 12" diameter pipe carries oil with a velocity distribution of v = 9(r1^2 - r^2) determine the average velocity and the value of kinetic energy correction
As shown in the figure, the water flows from the ground floor of a three-storey house to the second floor through pipes of 20 mm diameter (average roughness of the pipe material = 0.0015 mm) at a volumetric flow rate of 0.75 L / s. Water is discharged from the system to atmospheric pressure through a tap with a 12 mm diameter outlet. There are 4 winged elbows, one ball valve and one faucet throughout the installation. Calculate the effective pressure at point 1. (psu=998 kg/m3, usu=1.12x10-3 Pa s, g=9.81 m/s2)
Question 8 download image D The water in a large tank exits through a horizontal circular pipe of diameter D=0.01m and length L=94m. The centre of the exit of the pipe is h=1.0m below the water surface. We can assume that the flow entrance to the pipe is smooth so that there are no minor losses. The flow in the pipe is laminar, the friction factor can be assumed constant and can be found from h fD=64/Rep where the Reynolds number is based on the pipe diameter and mean flow speed in the pipe. Taking frictional losses into account, solve the resulting quadratic equation to calculate the speed of the flow out of the pipe. Give your answer in m/s to 2 decimal places. Use: kinematic viscosity given by v=0.00000114 m²/s density of water given by 1000 kg/m3 acceleration due to gravity of 9.81 m/s² A Moving to another question will save this response. >>
A pumping system has the following characteristics, f=0.015 length of the pipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipe is cast iron, and the system curve is: Hp= 34+ 5.47Q2 Knowing that the system curve and the pump curve intersect at 12 cfs a. Determine Operation head b. Determine discharge c. Plot the system curve
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
Q.9) If the faucet (gate valve), at E is fully opened and the pump produces a pressure of 350 kPa at A, determine the flowrate out from the faucet at E. The valve at B remain closed. The pipe has an inner diameter of 30 mm, and f=0.01. Include the minor losses of the tee (K=0.4), the two elbows (K=0.9), and the gate valve (K=0.19). 0.65 m 3 m B 5 m
10. Water at 25 °C is transferred 10 m high to the first floor using stainless steel pipes (e = 2 x 10-6 m) with a diameter of 2 cm. If the water leaves through a faucet of diameter 1.3 cm at a flow rate of 8 x 104 m³/s. Determine the required pressure at point 1 (P1) if: a) All viscous effects are ignored b) Only major losses are considered c) All loses are considered (major + minor) Assume that the density and viscosity of water at 25 °C is 997 kg/m and 0.891 x 10-3 kg/m.s, respectively. You can use relevant tables and Moody chart to find the required properties. L=4m L-4 m L= 4 m K, = 2.5 10 m K- 1.5 K, = 0.5 L= 4 m K, 8 Water L=5m L%3D4M