3. A simply supported beam has a span "L" carrying a distributed load that varies linearly from "0" at the left support to "w" (KN/m) at the right support. Determine the location of the maximum moment from the left support. a. 0.577L c. 0.677 L b. 0.477 L d. 0.377 L 4. Refer to problem 3, what is the maximum moment? a. 0.06415 L² c. 0.07415 L²

3. A simply supported beam has a span "L" carrying a distributed load that varies linearly from "0" at the left support to "w" (KN/m) at the right support. Determine the location of the maximum moment from the left support. a. 0.577L c. 0.677 L b. 0.477 L d. 0.377 L 4. Refer to problem 3, what is the maximum moment? a. 0.06415 L² c. 0.07415 L²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

NEED IN 1HOUR PLS THANKS From the figure, compute for the horizontal and vertical component forces of the hinge at B acting upon member AC as shown.
The truss shown is supported by a pin at A and a roller at F. Two force are applied to the truss. The force at C in directly above F., All the truss members are 3m long making equilateral triangles. Detemine the force in member CD. The answers have units of kilonewtons. 5 kN 3 kN BE
Determine the nominal moment strengt of the irregular beam shown. Assume the area of 25 mm rebar is 510 sq. mm. Given: a.) fc' = 35 MPa; fy= 413.70 MPa b.) fc' = 21 MPa; fy = 413.70 MPa
Problem 1 An angle bracket ABC is restrained by a high strength steel wire CD, and it supports a load P at A, as shown in figure. The strength properties of the wire and the shear pin at B are , = 350 MPa (wire), and t-300 MPa (pin at B). If the wire and pin are to be sized to provide a factor of safety of the wire F.S = 3.3 and a factor of safety of the pin F.S = 3.5. What are the required diameters of the wire (to the nearest mm) and the pin (to the nearest mm)? D 90 mm 20° 100 mm View a-a of B P = 2 kN
Determine the internal normal force at point C of the beam. Give your answer in N and to 3 significant digits. 200 N/m commu 3 m C 3 m 400 N/m B
A 72 2 (a) 8 W+ W 2 (c) 2 2W+ с W) 2 T 72 30⁰ A beam AB of length 1 and weight w supports a load W at its free end B and is hinged at its end A. A wire CD supports the beam at the mid point C making an angle of 30° with the horizontal. What is the value of tension T in the wire CD? D B W (b) 4 (2W + w) (d) 4 W+ W 2
Determine the internal normal force at point C of the beam. Give your answer in N and to 3 significant digits. 200 N/m nguni C -3 m- 400 N/m 3 m B
Question #2 Neglect the thickness of the beam. Determine the total moment of the forces: i) about point A ii) about point B F2= 40 N 70° 22 m 34 m -97 m- F1 = 50 N 67° A Answer: MoA 3,023.78 N-m cw; MoR = 1,246.49 N-m ccw -54 m- B
15 - In the plane truss system, the loading status of which is evident in the figure, the support reactions and all rod forces will be found. A is the fixed joint and B is the sliding joint. Single upload P = 35 kN, dimensions a = 1 m and bar numbers are given. Accordingly By = ? A) 35B) 99C) 70D) 49.5E) 140
H.W2: For the truss shown below find the horizontal and vertical displacement of joint C. if member AC was made of 1 cm long and placed in its position. 4m D A 90 3m B
You must show FBD for all problems 1. For the beam shown below, a) Find all reaction forces. The support at C is a roller. b) Determine the shear force and moment at the immediate left side of point B, and show value and direction on the FBD c) What are the shear force and moment at the free end D? 40 kips A B 4² E w = 4 kips/ft 10'- EC D
ZOOM MANN QUA MUKANA 5.25 A beam (EI= constant) of span Lis subjected to clockwise moments Mat both the ends A and B. The rotation of end A works out to be M BA