3 t/m 10 t 8 tm H. 4 m 3 m 6 m

Q: In the figure below, A, B, and C are all pin-connected, while D and E are fixed. With x = 9.3, what…

A: Sign convention:  Upward vertical force = positive  Downward vertical force = negative…

Q: 3,000 lb 1,000 lb 15 5' 10' 30 R2

A: Given:-  A beam is resting on two end support carries two concentrated loads P1= 1000 lb P2 = 3000…

Q: Q1: Draw the internal loading diagrams (N, Ty, Mx). State the extremum values on the diagı 2 kN/m A…

A:

Q: Find the joint forces in the system shown.

A:

Q: Find the force in EG shown in the figure

A: Equiulibrium about y∑ Fy=0-5+FFGsin60=0FFG=5sin60FFG=103kntension

Q: Q1: determine the magnitude and location of the resultant force of the force system shown: 40 lb 30…

A:

Q: 2) A beam loaded with both transverse and longitudinal loads as shown. This beam loading is typical…

A:

Q: Find the forces in members EJ and HJ of the roof truss shown in the figure.

A:

Q: Using the method of equations, determine the reactions, normal force, shear, moment and elastic…

A:

Q: Find support reactions and internal joint forces. Select a value such that the distance X is between…

A: Consider the free body diagram of the given frame as shown below. Take, X=2 m and Y=4 m.

Q: The magnitude of a resultant force based off of two vectors

A: Assume the vector forces F1 and F2 acts on a body and the magnitude of these vector forces are…

Q: Refer to the figure, what is the reaction at support B in kN? 12 kN 3 m 3 m C D 4 m 8 m 15 kN 4 m В…

A: A loaded frame structure is given and it has been asked to determine support reactions at B. Please…

Q: A circular lamina of 1000 mm in diameter is immersed in water so that the distance of its perimeter…

A:

Q: w kN/m A %L Lm

A:

Q: Please solve this problem step by step so I can understand

A: Please see the attached images for the solution.If there are queries or if the images are not…

Q: 2.4. Determine the resultant of orces system shown in Figure below and locate it with respect to…

A:

Q: A force of 50 kips is applied to a horizontal beam in a negative sense at an angle of 45 degrees at…

A: Note: As you have not mentioned the type of beam so we are assuming that it is an simply supported…

Q: A body having a mass of 30 kg rests on a smooth plane inclined at 20° to the horizontal and held in…

A: Given: Mass = 30 Kg Inclination = 20° Required : Horizontal force and normal reaction

Q: Given the beam loaded below, compute the following: a. Reaction @ support A b. Reaction @ support B…

A:

Q: In the figure below, A, B, and C are all pin-connected, while D and E are fixed. With x = 6.0, what…

A:

Q: I do not understand where you got these 4 equations numbers, and why all it divided by 3? Can u…

A:

Q: Q2/ A simply supported beam supports the applied loads and moments as shown, calculate the support…

A: To find support reactions

Q: A B C -30² +84/4 -22- E ---8-2 -22- G -12- H

A:

Q: Can you answer this please; What is the vertical support reaction in support B. Enter your answer…

A:

Q: Consider the truss shown in (Figure 1). Suppose that W₁ = 650 lb/ft and W₂ = 400 lb/ft. The…

A: Answer  Length of w1 and w2 load = 482+202 = 52 ft In order to get y component of reaction at A…

Q: What is the resulting force from the distributed load shown below?

A:

Q: In the figure below, A, B, and C are all pin-connected, while D and E are fixed. With x = 11.6, what…

A:

Q: A simply supported beam of length 2L is subjected to a uniformly distributed load 2w per unit length…

A: For simply supported beam,Length :2L uniformly distributed load : 2w per unit length To find the…

Q: Q4 For the simply supported beam shown below, what are the support reactions? 8N 5N 3N A B 1m 2m 2m…

A:

Q: Given the following, Determine the reactions for the beam. Show and explain step by step so I can…

A: Considering the given figure: 2P = (2)(5) = 10 lbP = 5 lbL = 12 ft  Explanation:In order to get RAV…

Q: 10 kN/m 10 kN/m A C 6 m 8 m 4 m

A: Finding out forces at A and B .

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.