- 3 m - 6 m- В A C Probs. 6–9/10

Q: Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment…

A:

Q: The uniform link AB, has a mass of 3 kg and is pin connected at both of its ends. The rod BD, having…

A: The given figure is shown below:

Q: B fm fm Draw the influence line for the beam Use Müller-Breslau's Method 1 Reaction at A 2 Reaction…

A:

Q: 3. Construct and draw influence lines for the reactions at(ACand E, the shear at D the moment at D,…

A:

Q: Draw the influence line for shear force Vc. Enter the magnitude of your and G influence line when…

A:

Q: C-2 A uniform live load of 300 lb/ft and a single live concentrated force of 1500 lb are to be…

A: Given data:- The given uniform live load, =300 lb/ft3 The concentrated force, = 1500 lb The given…

Q: Draw the influence line for the vertical reaction at A and the internal bending moment at C for the…

A:

Q: - Reaction at A, shear at section 1---1, and moment at C. by using muller breslau principle. Write…

A: Muller Breslau principle it uses influence line diagram

Q: Determine the (a) maximum reaction at A, (b) maximum positive moment and, (c) and maximum shear at…

A:

Q: Maximum axial force on EF.

A:

Q: A 6 m- B 31 с 3

A:

Q: Using the Muller-Breslau method, draw the influence line for the vertical reaction in A, cutting in…

A:

Q: 2. Determine the smallest moment of inertia required for the beam shown, so that its maximum…

A: Please upload one question at a time

Q: A uniform live load of 0.25k/ft. and a single concentrated live force of 3 k are to be placed on the…

A:

Q: -2m 2 m F B E A D - 2m – -2 m -2 m 2 m -2 m

A: We have draw influence line for shear panel BC and moment at D.

Q: d live load of P kN. Determine (a) the maximum positive (upward) reaction at B, (b) the maximum…

A: For the above beam, Assume W1=87N/mW2=4kN/mP=3kN

Q: Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the right of the…

A:

Q: Determine the maximum moment and the maximum shear in the girder bridge due to the truck loading…

A:

Q: Draw the influence lines for (a) the vertical reaction at A. (b) the shear at C, and (c) the moment…

A: Given data in question  Span member length  To find out  ILD NOTE We will draw ILD using Muller…

Q: 1 kN/m, a live load of 2 kN/m, and a concentrated live load of 52 kN. Determine the following:…

A:

Q: 2. Draw the influence line for the force in (a) member EH and (b) member JE. M C B D E F m-4 m 4 m 4…

A: Given :

Q: A uniform live load of 2 k/ft and a single concentrated live force of 6 k are placed on the floor…

A:

Q: 4. For the compound beam and loads as shown, find (a) the maximum reaction at C (b) the maximum…

A: I have solved this problem in detail although I have used it by logic and by self inspection which…

Q: Draw the influence line for the shear at C. Plot numerical values every 1.5 m. Assume A is fixed and…

A: Applying load on beam and the load is moving towards A to B Deflection at B is…

Q: 6.12 Draw the influence lines for (a) the vertical reaction at B, (b) the shear just to the left of…

A:

Q: QI/- Draw the influence lines for (a) the vertical reaction at G, (b) the vertical reaction at D,…

A: Given data in question  Span member length  Overhanging beam  To find out  ILDs  Note We will draw…

Q: Draw the influence line for the force in member GB of the bridge truss shown. SHOW THE COMPLETE…

A:

Q: b.) Using the value for F1,min that you calculated in (a), replace the two forces F₁ and F2 with a…

A:

Q: Draw the influence lines for (a) the vertical reaction at A, (b) the vertical reaction at B, and (d)…

A:

Q: 6-13. Draw the influence lines for (a) the moment at C, (b) the shear just to the right of the…

A: The question is based on a section supported on hinge and roller support. The length of the span is…

Q: (2) Draw the influence lines for (a) the vertical reaction at B, and (b) the moment at E. Assume the…

A: The continuous beam with an internal hinge is shown in the above figure. We have to find out the…

Q: B A+B ce line for the vertical reaction at A, what is the maximum ordinate? what is the ordinate at…

A:

Q: Draw the influence line for the force in member CD.

A:

Q: Replace the loading by a single resultant force, and specify the location of the force measured from…

A: (a) Replace the loading by a single resultant force, and specify the location of the force measured…

Q: Determine the reactions at the supports A and B of the compound beam. Assume there is a pin at C. A…

A: CONSIDER BEAM AC

Q: H.W1: Use the redundant is the moment at A W BA

A: Given Data: Length is L. Uniformly distributed load is w.

Q: #2 Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the…

A:

Q: The truss shown carries the following uniform live load and concentrated live 3 m D A 3 @4m 12 m…

A:

Q: 10 ft- A -10 ft. C -10 ft- B -5 ft-

A:

Q: Draw the influence lines for (a) the vertical reaction at A, (b) the shear at C, and (c) the moment…

A: Lo = 5 +4 + 7+3 = 19

Influence Lines

The graphs that show the variation of a function at a specific point on a beam or truss due to a unit load placed at any point along the structure are known as influence lines in engineering. Some common functions that are studied with influence lines are shear, moment, and deflection. In designing beams and trusses, it is important to use influence lines in structures where loads would move along their span such as bridges, crane rails, conveyor belts, floor girders, etc. The influence lines help to study where a load will create the maximum effect for any of the functions.