3) Find the magnitude and direction of the resultant force and moment at A FORCE lbs R= e MR = e Rx = 80- F= F.Cos(e) F, = F.Sin(e) Ry = 800 MR Forces = -100/1 +MA M=Fxd Couples -M,

Q: P. = 30KN Pz = 20KN 4m a = 1 L = 6m R2

A: Let R1=RAR2=RBRA+RB=50KN∑MA=030×1+20×5-6RB=0RB=21.666 KNRA=28.334 KN

Q: Find the the value of the internal force member CA; Note: Support at A is a Pin and Support at B is…

A: Please refer the attached image for complete solution. THANK YOU.

Q: The force in member AB of truss joint B shown in figure is given a 15 N B• - 10 N AB

A:

Q: Calculate the moments at the joints and supports. Draw the shear and bending moment diagram. Support…

A: Fixed ends moment:   MFAB=-wl212=-32*2212=-10.67 KN.MMFBA=wl212=32*2212=10.67…

Q: Generate the stiffness matrix for the frame corresponding to three degrees of freedom 1, 2, 3…

A:

Q: Please help me answer this. Thank you!! The steel framework is used to support the reinforced stone…

A:

Q: In the following problems solve the value of internal force member in the truss using the method of…

A:

Q: A 60° 42 B

A:

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

A:

Q: Solve the following problem and show your complete solutions. Explain your answer for better…

A:

Q: The truss shown below is pined at A and has a roller at F. The Load applied at E is P=20 kN. The…

A:

Q: 4. Replace the force system by an (a) equivalent resultant force and (b) couple moment at point 0.…

A: The given figure is shown below:

Q: Determine the force in members CE, CF and BF for the truss loaded as shown. Ans. BF = 0.289P (T) B…

A:

Q: From a continuous beam as shown in the figure. Assume that the cross section is uniform length and…

A: solving this continuous beam using the three-moment equation, Consider dummy span OS on the left…

Q: For determining the force in AB of the truss shown in the figure below by method of sections, the…

A:

Q: 6 kips 2 kips/ft В D 6 ft 6 ft 2 ft The beam is subjected to the load shown. Determine the equation…

A: Let,RA=vertical reaction at support A in upward directionRC=vertical reaction at support C in upward…

Q: From the figure shown below, the length of member AB is 8m and member AC is 5m. If force F is 360N,…

A:

Q: A propped cantilever beam is loaded as shown. Determine the reactions at A and D (positive if the…

A:

Q: Determine the equation of the elastic curve. EI is constant.

A: Consider the free body diagram of the beam shown below. Consider the moment equilibrium about point…

Q: Determine the maximum bending moment magnitude for the beam shown below. Use a = 18 ft, b = 6 ft,…

A: Solution:- Bending moments at various sections: BMC=0BMB=-6×6×62 =-108 kip.ftBMA=-6×24×242+96×18 =0…

Q: Find the force in members JI and DE and whether they are in tension or compression. H 1.5 m FEO 1.5…

A:

Q: Using the method of sections and cut line aa, = calculate the force FCF in member CF of the truss if…

A:

Q: a. Find the value of the moments at the ends of each element. b. Find the value of the horizontal…

A: For the given frame we have to find moments at the ends of each element and horizontal reaction at…

Q: The following beam is subjected to bending. Consider cross-section K! IF K + 1/2 + 1/2 + y. + A a +…

A: F = 15 kN l = 2.4 m a = 80 m v = 5 mm e = 2.23 cm I1 = 77.65 cm4 I2 = 18.178 cm4

Q: B W W= 500 N Determine the force developed in each member.

A:

Q: A symmetrical beam cross section is shown below. The centroid is in the exact centre of the section.…

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Given,

Q: 2. Determine the internal normal force, shear force, and bending moment at point A in the rod. The…

A:

Q: Date : 1. 5.1m 十 十L十t 7. 741

A:

Q: P. = 30KN P2= 20KN a = 1 L = 6m R: R2

A:

Q: Problem 5 Knowing that the radius of each pulley is 3 in., the load P is 500 lb, and neglecting…

A:

Q: 5. Determine the pin reactions at A and all forces acting on member DEF of the frame shown. Neglect…

A:

Q: Using the method of sections and cut line aa, calculate the force FCF in member CF of the truss if P…

A: Given :

Q: -3 ft 3 ft 3 ft D - B 2 ft 上 4ft H. 6 ft E G.

A:

Q: o In total, there are Σ F, = 0. : A, = Σ ΜΑ = 0 : Ex = ΣFx = 0: Ax= 2. Free body: member CDE: Mc =…

A:

Q: Determine

A:

Q: A 30 80lb 30° 60° C B Q= 30lb

A: An arrangement of forces have been given and it has been asked to determine force in member CB and…

Q: 0.4 m 2 m 2 m 2 m В

A: Given data: Calculate the buckling load:

Q: Using the method of sections and cut line aa, = calculate the force FCF in member CF of the truss if…

A:

Q: complete solution and drawing. if u can please add some explanation thankyou FN = 49  MN = 101…

A: Ee have to determine the value of reactions and forces (internal loadings) for points A, B, C, D and…

Q: A force F= 338 N is applied as shown to the bracket ABC. a=134 mm; b=54 mm; c=90 mm; B=33 in degree.

A: simple bending - A line joining length centroid of all cross section along the length of a  beam is…

Q: Using method of sections, determine the reaction at A, the force in members BD, FE and CE if…

A:

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.