3) Find the current flowing in the 9 2 resistor using Thevenin's Theorem.18 v12014Ω1094.998

To find out the Thevenins voltage then open the 9 Ω Resistor Current flow in the circuit,…

Answered: 3) Find the current flowing in the 9 Ω…

Engineering

Electrical Engineering

3) Find the current flowing in the 9 Ω resistor using Thevenin's Theorem. 18 v 12Ω 14Ω 109 4Ω 9Ω

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.66P

See similar textbooks

Related questions

Q: a 5kva, 757v/ 420V, single-phase transformer has the percentage regulation drops 4%. determine the…

A: KVA rating S = 5 KVA. Primary voltage at no load E1=757 V. Secondary voltage at no load E2=420 V.…

Q: What is the capacitance of system 23? C23 - F What is the capacitance of system 123? C123 - F What…

A: For the given circuit the value of capacitance in each branch and the total capacitance needs to be…

Q: • We wish to analyze the transistor amplifier shown in the figure to determine its voltage gain.…

A: For the given amplifier circuit the voltage gain of the amplifier needs to be calculated. The…

Q: 4. a. Design a combination of at least one resistor, one inductor, and one capacitor in series to…

Q: (d) Find the Thévienin voltage Vth and impedance Zth for the circuit shown in figure 8.

Q: A four-pole, three-phase induction motor drives a turbine load. At a certain operating point the…

Q: Assigning R3 as the load, find the following: R₁ 40 VS1 28V R₂2 201 R₂ (Load) 10 7V VS2 ...…

A: VTH= Voltage across the load R3 RTH= Equivalent resistance across the load We need to calculate…

Q: 3) Find Vo in the network 24V (+ 3 ΚΩ 6 ΚΩ ΜΜ 4 MA 12 ΚΩ 6 ΚΩ 4 ΚΩ www 8 ΚΩ 12 ΚΩ 4 ΚΩ + Vo

A: In this question we need to find the voltage Vo shown in the given circuit. We use nodal analysis…

Q: In the circuit below, determine the power dissipated in the 10ohm resistor .

A: For the given circuit the power absorbed by the 10ohm resistor needs to be calculated. The node…

Q: Find the Norton equivalent with respect to the terminals a,b for the circuit in Figure 1) if v 20 V,…

Q: 1) Create the state table 2) 2) Find A((t+1), B(t+1) and Y(t_ 3) Draw the circuit

Q: Determine Vo for each network circuit.

A: For the given diode based clipper and clamper circuit the output voltage of the circuit needs to be…

Q: How much power is dissipated in the 45 Ω resistor in the circuit shown? 10 V 45 Ω 10 Ω Μ 33 Ω 6 Ω 10…

A: Voltage source V=10 V Given the resistance all are Ω Find out equivalent resistance, from the…

Q: Q2 ) A 220-V, 1.5-hp 50-Hz,wo-pole, capacitor-start induction motor has the following main-winding…

A: As per the guidelines of Bartleby we suppose to answer first three subpart only for solution of…

Q: 3. If the switch changes position (from a-b to b-c) at t-0, find the inductor current it(t) for t20.…

A: given that y = 1 to find energy stored in the inductor is E at t = 5 milliseconds

Q: Refer to the following figure. The circuit is a

A: Need to identify the given circuit name and its function. The circuit function is based on the…

Q: Convert the computed TEC into NEC. THEVENIN'S EQUIVALENT CIRCUIT (TEC) RTH VTH R3 (Load) NORTON'S…

A: Norton's equivalent circuit is converge of Thevenin's equivalent circuit. To convert TEC into NEC,…

Q: Find the power of the dependent source.

A: Need to calculate the power of the dependent source present in the given circuit. THe required…

Q: #1) FIND the value of the load RL in the network that will achieve maximum power trauster and…

A: In the given questions we need to calculate the thevenin equivalent parameter and Pmax to load.

Q: Which of the following is true for a common-base amplifier? O a. The base is not connected O b. The…

Q: Q3) Mention Methods of starting of three phase induction motors and Single phase motors Discuss with…

A: Step-1-> There are different methods of starting three-phase induction motors. The following four…

Q: A discrete-time system is described by the following equations Го 3 07 27 x(k+1)= 0 2 1x(k)+ 1u(k)…

A: The state-space model of a discrete-time system is given as xk+1=030021110xk+21-1uk,yk=021xk. We…

Q: 2. Design PID for control system has the following open loop transfer function, 6 G(s): s(s² +8s…

A: Given open loop transfer function, Gs=6s(s2+8s+12) now to design the PID controller for follwoing…

Q: 10- The following channel matrix has P(X) = [.5.5] ‚= [²o¹² p² P(Y/X) = 1-pl -р р 0 a. Draw the…

A: PY/X=1-pp00p1-p PX=0.50.5

Q: ►FIGURE 2-103 11:36:57. 37. Draw the output voltage waveform for each circuit in Figure 2-103. 38.…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: For the circuit shown, the switch goes from closed to open at t=0. What value does the resistor R2…

A: Here , 2oder RLC circuit is given Where Is=1mA, R1=1.7kohm , L=40mH,C=90nF At t=0 switch is closed…

Q: (a) What is the kinetic energy of a 2440 kg car that is traveling at 78 km/h? kJ (b) How much work…

A: Given that,Mass of the car, m=2440 kg.Speed, v=78 km/h.converting km/h into ms,v=78×103 m3600…

Q: R₁ 4Ω VS1 28V R₂ C 202 R₁ (Load) 10 7V = VS2 THEVENIN'S EQUIVALENT CIRCUIT (TEC) RTH VTH R3 (Load)

Q: Q2) For the single line diagram shown in figure below, find the (L-L) and (L-L-G) fault current at…

A: For the single line diagram shown in figure below, to find the (L-L) and (L-L-G) fault current at…

Q: 1- A Level includes PIDs and PLCs under the automation pyramid (Management, Field, Control, SCADA)…

A: Automation pyramid is arepresentation of the various levels of automation in the industry. it…

Q: Short Answer Questions: (Show your workings clearly & use x-3.14159 if necessary) With reference to…

Q: Please draw the Vo and determine the maximum value of Vo.

Q: 5. The three-port device with an s-matrix of s= 1 0 a. Directional coupler b. Wilkinson power…

A: "Since you have posted multiple questions, we will provide the solution only to the first question…

Q: 4.54 Find the node voltages in the circuit shown in Fig. 4-42. Ans. V₁ = 5 V, V₂ = -2 V 20 A V₁ 2 S…

Q: Use KCL to calculate the unkown current / in the circuit below: 2 A O-4A -8 A 3 A

A: Circuit diagram:

Q: Find the power developed by the source v..

Q: 4. The total power absorbed in the circuit is W. 5. Is the total power balanced in this circuit.…

Q: In a flux meter the air gap flux density is 0.04 Wb/m2, number of turn on moving coil are 50 & the…

A: A flux meter- Air gap flux density=0.04 Wb/m2 Number of turns on moving coil=50, Area of moving coil…

Q: What are buck and boost converters and how are they used in power electronics?

A: Buck and boost converters are types of power electronics circuits that are used for voltage…

Q: Q.2: Using nodal analysis, obtain vo in the circuit shown below: 3 Ω ΖΩ ΣΩ Μ 3 V ΤΩ 4%

Q: (a) Derive AF, the forward loop voltage gain, for this circuit. (b) What is AF if R3 » R4 and if R3…

Q: IA VA + I V₁ ww R₁ + Consider the circuit above, where: Calculate: VA=6 V, R1-50, R2=8 0, R3=802 V₁…

A: Values are given as, VA=6 V, R1=5 Ω, R2=8 Ω, R3=8 Ω. Circuit diagram is given as,

Q: IA VA + I V₁ ww R₁ + Consider the circuit above, where: Calculate: VA=6 V, R1-50, R2=8 0, R3=802 V₁…

A: Values are given as, VA=6 V, R1=5 Ω, R2=8 Ω, R3=8 Ω. Circuit diagram is given as,

Q: 4. Determine i in the given circuit. SV (+ 32 M { +1 8 V

A: Circuit diagram is given as,

Q: 9V + + VD- + VD- +VD- 100Ω

Q: A medium is characterized by a = 0,₁ μ = 2μe and € - 5 €₁. If H = 2 cos (wt-3y) az A Calculate w and…

A: We need to find out the electric field and angular velocity given magnetic field.

Q: Calculate the impedance and the output voltage of the following circuit.

A: According to the question, for the given circuit as shown below We need to calculate the impedance…

Q: Determine the following for the network below. R1 = 1 kiloohm R2 = 3 kiloohm R3 = 3 kiloohm R4 = 3…

Q: 3) Find the current flowing in the 9 Ω resistor using Thevenin's Theorem. 18 v 12Ω 14Ω 109 4Ω 9Ω

A: We need to calculate the current following in the 9 ohm resistor using Thevenin's Theorem VTH= open…

Q: 4) Assume band structure of material is plotted in box model. Place Ep as such (i) material is…

A: Solution: =>Determine: here material is insulator , semiconductor and metal at all temperature…

Concept explainers

Thevenin Theorem

Any linear circuit, no matter how complex, maybe simplified to an equivalent circuit utilizing only a single voltage source and series resistance coupled to a load, according to Thevenin's Theorem. The superposition principle says that all foundational equations must be linear, and the notion of "linear" is still the same (i.e., there should not be any exponentials or roots). This is particularly the case when operating with passive elements like resistors, inductors, and capacitors. However, some components (particularly some gaseous and semiconductor devices like tunnel diode, Schottky diode, transistors like BJT, MOSFET) are nonlinear, meaning their current resistance fluctuates with voltage and current. As a result, circuits made up of these parts are known as nonlinear circuits.

Question

3) Find the current flowing in the 9 2 resistor using Thevenin's Theorem.
18 v
120
14Ω
109
4.9
98

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Find out the Thevenins voltage

VIEW

Step 2: Find out the Thevenins Resistance

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 4.5MF Copacitor to a 74 K A Arilo ohms resistor with ç=20ov. initially unchucged is connected and an emf sourse 1) current in th Ac Circvit immediatlu of ter Saritch s clored?: b)cuirentin Ke ciccuit AMor vera long time after Switch s closed> ) what is te Charge On the copurilor ofter a verq long time atter the Sw/tch s i's clordi 1 How long After the Smitch is Closed (cached 50%0 has the coporitm of idy Pinal voltage.
IEYGN9QmEpGpicor2WQ_ZtuQVINUKNNMTIMFBDWFFM consider the following circuit and find the contribution of the 2A source only in the value of Vx. 4Ω 50 Vx 10 A 2 A 3F= 20 0.2i 4 H O 4v otherwise 10 V BV O 6V
Write the current and voltage relations for the following two components. R R U U (a) (b)
Find the voltage at node P in the following figure V1 4V 9V b) 8V c) 10V d) 11V O a. 8 O b. 9 Oc. 11 O d. 10
SEARCH ASK CHAT MATH SOLVER Question A load is composed of a 4 ohm resistance connected in series with a 3 ohm inductive resistance. The load is connected across a 120 source. Compute: (a) current (b) voltage across the resistance (c) voltage across the inductor Recheck voltages using Vt=120 V
Deduce the function of the following circuit: 5V Q3 2N6804 -ru A 1kHz 5-V -ru Q2 Q1 2N6659 B 1kHz 5V. Y. 04 2N6804 2N6659 XSC1 {} to (3
find the current of loop 1 R6 · 150 R1 R3 180 200 R8 loop1 140 R5 =25V 0.757 0577 0.755
The currents at the junction point in a circuit have the following values I1 = (15 - j4) A and l2 = (12 + j22) A. Calculate l1 + l2
Refer to the circuit of Figure Find V when the controlling current I is the following: a. 20 MAZ0° b. 50 MAZ-180° c. 60 MAZ60° R = 1 KΩ 601 25 ΚΩ + 5 kΩ V
Determine the Thevenin voltage Vth with respect to terminal A-B. How much current will flow from node A to B once these two nodes are shorted? The circuit can found in the attached image.
The superposition technique can be described as a multi-step process of calculating the individual contribution of each source. Then, all of the individual solutions are combined to yield the final solution. 6 kn 12 V ww 6 kn Select one or more: DA-120 B. 0.80 C -0.75 D. 0.53 0.25 4 mA FO G +0.13 H. 0.50 +0.65 +0.92 1.00 +1.60 4 k 3 kn 10 Figure 3.1 If superposition is used to compute the current , in Figure 3.1, what are the individual solutions for Io (in mA) for each source? 2 mA Figure 3.1 If superposition is used to compute the current in Figure 3.1, what are the individual solutions for Io (in mA) for each source? 2 km2
6 Let Vab_c be the voltage when R21 is connected and Vab_d when RL21 is disconnected, find these peak voltages and current flow through R21. Express your result as IR21=900mA, Vab_c=5.3V, Vab_d=2.8V R20 6Q V6 8V a bl R21 3Ω R22 m 4Ω R23 20