3- Calculate the moment carrying capacity of the beam shown? Choose the rec reinforcement to carry this moment. d3470mm bw= 270mm and d'=30mm. C20: Allowable stress=7MPa S420: Allowable stress=220 MPa A, n=15

Q: A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a…

A:

Q: 4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the…

A: Given that :

Q: 4m + 6m EA 1 77777 D 4 rigid 5m 3 kN/m Figure-3 7m 4444 2EA B₁ 1 1 1 I The rigid beam AB in Figure 3…

A: To find the stress in bar 1 and 2

Q: Question 5 of 20 A structural member is fabricated with the cross section show below and is…

A:

Q: Pkips P/2 kips 10 ft 10 ft to 10 ft 10 ft El = constant Figure 5

A: MFAB=-wl8=-(38)(20)8=-90kipMFBA=+wl8=+90kipMFBC=-wl8=-18(20)8=-45 kipMFCB=+45  kip Restraining…

Q: For the frame shown, determine the maximum normal stresses (compression and tension) and the maximum…

A:

Q: 4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the…

A: Let Ra and Rd be the reactions at A and D Supports Considering equations of equilibrium, Ra + Rd =…

Q: 4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the…

A: Given data   Determine the safe allowable value of w0 if the flexural stress is limited to 160MPa in…

Q: The bracket shown in Figure ST - 228 is attached to a column by 6- 20 mm diameter bolts and loaded…

A:

Q: Ź The bar AC is absolutely rigid and is pinned at A and attached to bar of copper DB and bar of…

A: BD = Copper and CE = SteelEst = 200 GPa Ecu = 90 GPa  αst = 12 × 10-6 /°C αcu = 18 × 10-6 /°C ∆T =…

Q: Note: Please show all of the free body diagrams used and also show the complete solution. The beam…

A: Deflection will be determined by the first mentioned method i.e. double integration.For other…

Q: SITUATION III: The cross section of a tension member is shown below: Use Fy=275 MPa, Fu=400 MPa. 25…

A:

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A:

Q: lb concentrated forces were applied.

A: Reaction:RA=RB=30014+800+8002=2900lbMax shear = reaction =2900

Q: For the given properties of beam below. Compute the flexural capacity of the bea b = 380mm d = 430mm…

A: Based on given data:

Q: Determine the nominal strength for tensile yielding in the gross section. 1. B. 429.67 KN D.390.10…

A:

Q: Read the question carefully. Give me right solution according to the question. Find the load P in…

A: given data:- yield stress due to bending=250 mpaelastic constant E =200000 moamoment of inertia of…

Q: 3) Find a) the maximum stress in the shown member, b) the relative displacement between 8 and D (Ap)…

A:

Q: Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum…

A: Given that: E = 200 GPa

Q: The column shown in the figure is reinforced with 8 - 28mm diam steel with fy = 414Mpa and f'c =…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: Q2:If allowable stresses are at = max. value of W. W 2m 8m 165MPa, oc = 100MPa t = 70MPa determine…

A:

Q: Use AISC Equation E3-2 or E3-3 and determine the axial compressive strength oP for the following…

A: Consider the column as in the below diagram;

Q: Q1:If allowable stresses are o, 165MPa.0, 100MPa = 70MPa determine max. value of W. M 300mm Im 4m Im…

A:

Q: A horizontal member is looded and supported as shown. IOKN verfical support 0.3 m B 0.4m spring…

A:

Q: Q1:If allowable stresses are o, 165MPa.0, 100MPa = 70MPa determine max. value of W. M 300mm 100mm Im…

A:

Q: H.W.2: Find the maximum applied load (P) that can be applied on the rectangular beam with dimension…

A: Given a simply supported beam, spanning = 12m Carrying two point loads at 4m from either sides of…

Q: Determine the maximum shear stress if its used as a 8m beam simply supported at the left end and 2m…

A:

Q: The beam shown in the figure below has the following properties: 28-ft simple span f'c = 4000 psi,…

A: Given,  Length of beam, L = 28 ft  Compressive strength of concrete (f'c) = 4000 psi Unit weight of…

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A: Using equilibrium and compatibility establish the equation of equilibrium and solve them to get the…

Q: The beam cross-section shown below has 90 kip-ft of bending moment applies to it. calcul 6" T 8" 2"…

A:

Q: A steel bar AD has a cross-secțional area of 260 mm? and is loaded by forçes P, = 12 kN. P,= 8 kN.…

A:

Q: SAMPLE PROBLEM 1: Properties of W 30 x 116 d = 762 mm A W 30 x 116 beam has the top flange…

A:

Q: AT beam supports the three concentrated loads shown in Fig. P-556. N.A. is 3.5 in., INA = 97.0 in.…

A: Given data: INA=97 in4

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Given data The plate is fastened to the fix member by three 10 mm diameter rivets

Q: For the exact in the figure tensile strength = 8000 N/cm^2 compression safety = 3000 N/cm^2…

A: Allowable tensile strength is given as:Allowable compressive strength is given as:

Q: The steel beam has the cross section shown. The beam length is L = 4.2 m, and the cross-sectional…

A:

Q: For the given properties of beam below. Compute the flexural capacity of the beam. b = 390mm d =…

A:

Q: Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate…

A: