(3) A 8 lb collar is released from rest in the position shown, slides down the inclined rod, and compresses the spring. The direction of motion is reversed and the collar slides up the rod. Knowing that the maximum deflection of the spring is 6 in., determine 18 in.- (a) the coefficient of kinetic friction between the collar and the rod, 30° (b) the maximum speed of the collar. k= 60 lb/ft

(3) A 8 lb collar is released from rest in the position shown, slides down the inclined rod, and compresses the spring. The direction of motion is reversed and the collar slides up the rod. Knowing that the maximum deflection of the spring is 6 in., determine 18 in.- (a) the coefficient of kinetic friction between the collar and the rod, 30° (b) the maximum speed of the collar. k= 60 lb/ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Required information A uniform thin bar AB of length L = 5.5 ft is released from rest at an angle 0 = 0₁. As the bar slides, the ends A and B maintain contact with the surfaces on which they slide. A L B Neglecting friction and knowing that the end A has a speed of 18 ft/s right before hitting the floor, determine 0₁. The value of 0₁ is
Two steel balls, each of mass m = 1.84 kg, are welded to a light rod of length L = 545 mm and negligible mass and are initially at rest on a smooth horizontal surface. The distance b= 111 mm. A horizontal force of magnitude F= 27 N is suddenly applied to the rod as shown. Determine (a) the magnitude of the instantaneous acceleration a of the mass center G and (b) the magnitude of the corresponding rate 0 at which the angular velocity of the assembly about G is changing with time. m Answers: a = O = IN 7. 77 M m/s² rad/s²
A package is projected up a 15° incline at A with an initial velocity of 8 m/s. Knowing that the coefficient of kinetic friction between the package and the incline is 0.12, determine (a) the maximum distance d that the package will move up the incline, (b) the velocity of the package as it returns to its original position.
Pravinbhai
A force of P = 200 N is applied to block A and causes block A to accelerate to the right on a rough surface as shown in Figure below. Knowing that the mass for block A is 10 kg and the mass for block B is 6 kg. The coefficient of kinetic friction between block A and the surface is 0.15. Pulleys are massless and smooth. A 30° (6 + a) kg 6 kg B Determine the tension in the cable attached to block A. Explain with calculations on the possible way(s) to reduce the acceleration of block B.
A 4-kg collar A is at rest on a spring with stiffness k1 = 310 N/m, but the spring is not connected to the collar, when a force F of 220 N is applied to the cable. Knowing that A has a speed of 0.5 m/s when the upper spring is compressed 75 mm, determine the stiffness k2, in N/m ignore friction and pulley mass 450 mm peper 75 mm - 400 mm- F
Problem 12.F11 Disk A rotates in a horizontal plane about a vertical axis at the constant rate. Slider B has a mass m and moves in a frictionless slot cut in the disk. The slider is attached to a spring of constant k, which is undeformed when r = 0. Knowing that the slider is released with no radial velocity in the position r=ro, draw a FBD and KD at an arbitrary distance r from O. Spring Fig. P12.F11 60
A 74 g ball B dropped from a height ho=1.9 m reaches a height h₂= 0.25 m after bouncing twice from identical 250-g plates. Plate A rests directly on hard ground, while plate Crests on a foam-rubber mat. ho B hy Determine the height h1 of the ball's first bounce. The height h1 of the ball's first bounce is m.
A uniform rod BC of mass 10 kg is connected to a collar A by a 350-mm cord AB. Neglecting the mass of the collar and cord, determine (a) the smallest constant acceleration a for which the cord and the rod will lie in a straight line, (b) the corresponding tension in the cord. Hint: The smallest constant acceleration is attained when point C of the rod is about to leave the floor. ад A 350 mm 650 mm C B 450 mm
A system of blocks is pulled by a force P. The string connecting blocks A and B passes over a pulley whose coefficient of friction between string and pulley is 0.25. The coefficient of friction between surface and blocks is 0.20. Block A weighs 200N and block B weighs 300N. Determine, a. the minimum value of P for impending motion to the right. b. the tension connecting block B. B= 30° В A 30°
A spring is used to stop a 50-kg package which is moving down a 20° incline. The spring has a constant k =34 kN/m and is held by cables so that it is initially compressed 50 mm. Knowing that the velocity of the package is 2 m/s when it is 8 m from the spring and neglecting friction, determine the maximum additional deformation of the spring in bringing the package to rest. Assume that the kinetic coefficient of friction between the package and the incline is 0.2. 2 m/s 50 kg 8m Cable 20° The maximum additional deformation of the spring in bringing the package to rest is 0.574 x m.
Show the complete solution. Put notes on steps. In the system shown, a 150 N collar-pulley assembly slides on a horizontal shaft with coefficient of kinetic friction pk = 0.10 between the collar and the shaft, and is acted upon by a force P with a magnitude of P = 261.65 N at an angle e = 31.16° as shown. Knowing that the assembly is initially at rest, what is the velocity after 3s? Also, at this instant, find the tension in the cord and the velocity of block A.