3-17 A pair of ice tongs is shown in Figure P3-7. The ice weighs 50 lb and is 10 in wide across the tongs. The distance between the handles is 4 in, and the mean radius r of a tong is 6 in. Draw free-body diagrams of the two tongs and find all forces acting on them. Determine the bending moment at point A.

3-17 A pair of ice tongs is shown in Figure P3-7. The ice weighs 50 lb and is 10 in wide across the tongs. The distance between the handles is 4 in, and the mean radius r of a tong is 6 in. Draw free-body diagrams of the two tongs and find all forces acting on them. Determine the bending moment at point A.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.97P: The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces...

See similar textbooks

Similar questions

At a full d raw, an archer applies a pull of 130 N to the bowstring of the bow shown in the figure. Determine the bending moment at the midpoint of the bow.
The figure shows a wire cutter. Determine the cutting force on the wire at A when the 75-N forces are applied to the handgrips. (Hint: The horizontal components of pin forces at B and D are zero due to symmetry.)
Find the internal force systems acting on sections 1 and 2.
Find the internal force system acting on section 3 for the pin-connected frame.
A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). Draw axial-force, shear-force, and bending-moment diagrams for ABC.
3-1. Calculate the moment about point A (Figure P3–1). (Each section represents 1 ft2.) 26 lb//12 5. 34 lb 15 lb 3. 4 8. 15 30 lb FIGURE P3-1
3-5. Calculate the moment about point A in Figure P3-5. 800 lb A -5'→ 7' FIGURE P3-5 200 lb 64 3 3'→ 400 lb
3-7 The bending moment in the beam at point A is equal to the moment of the 800-N force about point A. Calculate the moment about point A (Figure P3-7). 800 N 38 Figure P3-7
Find the moment about point A for the lever shown in (a) Figure P3-24a and ( 30 N A 70° 70° .1 m .3 m 30 N FIGURE P3-24a
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
In the given figure below was supported at A and E by with a ball and socket and a wire at D connected to F. Determine the following given that force is equal to 687.4N: Determine the X-component of Vector DF Determine the Y-component of vector Df Determine the z- component of Vector Df Determine the moment experienced by the system assuming that there is no wire support. determine the x-component of the moment experienced by the system assuming there is no wire support Determine the y component of the moment experienced by the system assuming that there is no wire support Determine the z component of the moment experienced by the system assuming that there is no wire support determine the tension experienced by wire Df Determine the x component of the tension experienced by wire DF determine the y component of the tension experienced by wire DF Determine the z component of the tension experienced by wire DF Xb: 171. 995 xC : 477.445 Ya:200.266 ZE : 150.166 Zf : 492.252
6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in