Determine the following beam.1) Determine the reactions at the supports.2) Determine the magnitude and location of the max bending moment.3) provide a shear and bending moment diagram for the beam. The image depicts a structural beam analysis diagram involving various loads and supports.1. **Beam and Supports**: - The beam is supported at two points. The left support is a triangular representation of a pin support, providing both vertical and horizontal reaction forces. The right support is a roller support shown with a triangle atop a rectangle, providing only vertical reaction forces.2. **Loads**: - At the far left end of the beam, there is a concentrated load of 100 lbs. - Along the beam, there is a uniformly distributed load of 25 lbs/ft extending over a specified section. - At the far right end, a concentrated load of 75 lbs is applied.3. **Beam Dimensions**: - The distances between various loads and supports are marked: - From the left end to the roller support, the distance is 4 feet. - Between the portions of distributed load and points where measurements are not labeled, indicate sections are 3 feet and 4 feet, as shown.This diagram is typically used in structural engineering to determine reactions at supports and internal stresses such as shear forces and bending moments across the beam.

Answered: Image /qna-images/answer/aa0887eb-c916-4749-a4a4-c9de2c25a769.jpg

Answered: 25 lb / ft 100 Ib 75lb 4ft 3ft 4ft 3ft

Engineering

Civil Engineering

25 lb / ft 100 Ib 75lb 4ft 3ft 4ft 3ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

65 ll docs.google.com/forms/d/e, :D determine the force in member AB for.5 the truss show in fig, if the reactions at supportes A and B is Ax= 25kN to the left, Ay= 5kN up ,and By= 35kN up 40kN G. 5KN 4m 10kN C 10KN F D!E 4m A B 2m Im,Im, Im!lm 2m 22.5 kN (T) O 32.7 KN (C) 32.7 kN (T) 27.9 kN (C) O أخرى Classifv the fram show in in Fia. as .2
1. Determine the reactions at the supports of the beam loaded as shown below: 4 A 10cm 12N 5600 B 10cm C 5cm 6N D
Determine the maximum shear in kips for the beams shown below using the method of consistent deformations. Select the reaction at the interior support to b the redundant. two decimal
Using the method of consistent deformations, choose Ax as the redundant reaction. Given A = 10 in², and E = 30000 ksi. Find all reactions and all member forces in the indeterminate truss. 30k B >10k 20K 111 12'
3) A plane truss is shown in the figure. 3-a) Determine the support reactions. 3-b) Find the forces in the members 1, 2, 3, 4, and 5. a = 2 m b=1m P = 10 KN b V a H U a D P a Q = 4 kN| U (4 B a E 5
A two-dimensional truss is subjected to horizontal load 10 kN and vertical load 5 kN at Fand Drespectively as shown in figure below. The force in the member DFIS kN. 5 KN 4 m D 2 m 2 m 10KN 4 m
For the determinate 2D truss shown:(a) Compute the reactions and the internal forces of all the truss elements using the methodof joints.(b) Compute the reactions and the internal forces of all the truss elements using the method
1.3-6 Consider the plane truss with a pin support at joint 3 and a vertical roller support at joint 5 (see figure). (a) Find reactions at support joints 3 and 5. (b) Find axial forces in truss members 11 and 13. 20 N 45 N 4 5 5 6 7 12 11 7 10)2 m 13 9 8 60 N 1 2 3 4 2.5 m 2 2 m 1 m PROBLEM 1.3-6 3.
Draw the shear force diagram and the bending moment diagram of the bridge girder shown below. FAC = 84.1K (T) Fec 84.1K (T) FCD=64.7 K (c) 5 ft A 12 ft- 80 k D C 12 ft B
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 30 kN, P2-50 kN, P3=20 kN and P4-60 kN, a= 3 m and h=2 m, you are required to: P2 F a A and F. P1 E G a H I A D a h h B| h P3 P4 a) Determine the reactions at the supports b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint F. d) Using the method of sections, determine forces on members ED, EH, GH. e) Using the method of sections, determine forces on members DC, HC, HI.
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 30 kN, P2-50 kN, P3=20 kN and P4-60 kN, a= 3 m and h=2 m, you are required to: P2 F a A and F. P1 E G a H I A D a B h h h P3 P4 a) Determine the reactions at the supports b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint F. d) Using the method of sections, determine forces on members ED, EH, GH. e) Using the method of sections, determine forces on members DC, HC, HI.