235 mm 115 205 mm mm 50 mm 90 mm 140 mm Answers: i mm y = i mm i mm II IN

Q: To print out a and b given below, which printf() statement would you use? float a = 3.14; double b =…

A: Given:- To print out a and b given below, which printf() statement would you use? float a = 3.14;…

Q: You are required to measure the area of a site by tape only. The needed length measurements are…

A: Given that:                   Length of sides are: A=12, B=30, C=25, D=25, E=22, F=20, G=25, H=35,…

Q: 1)Given the following set of stadia level notes. The instrument used has a stadia interval factor of…

A:

Q: Lloukle Inte gr ation Meth od Lletermine the ff :). LDefle etion at e). Mope at C

A:

Q: ****************** Draw a flowchart to find the sum for the following numbers: Sum= 6 + 10+ 14 + 0

A:

Q: Complete the following set of profile level notes and show the customary arithmetic check.

A: To Compute The given set of profile level notes and show the customary arithmetic check.

Q: INSTRUCTION: Solve the diagram given below. Determine the ff items rounded to two decimals. 40 kN 25…

A: Step 1: solve for reactions Step 2: draw shear and moment diagram Step 3: determine the maximum…

Q: 3. For the data tabulated, calculate the volume of excavation in cubic yards between stations 10 +…

A: Volume of excavation (V) = Average area × Length= A1 + A22×L27               ( 27 ft3 =1 yd3 )where,…

Q: A railroad curve has Dc = 4°00', I = 24°00', and PI station = = 35+ 45.00 ft. Use the chord…

A:

Q: Txs Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an…

A: Given data:- σxA,B=59.2σsA,B=118.5τxsA,B=118.5 Below diagram is given;

Q: E D А B P T

A: Static friction is contact between at least two strong masses that are not moving comparative with…

Q: A schedule is an organized sequence of events that identifies all parts of the work to be done. O…

A: Schedule is the organizes tasks, resources, and deadlines in the ideal order for the project to be…

Q: Use bisection, newtons, secant and regula falsi methods.

A: AS EQUATION IS GIVEN WE NEED TO SOLVE BY DIFFRENT METHIOD AS B PART HAS TO BE TAKEN MEANS BETBEEN 1…

Q: 0.9 Chart Title 0.8 0.7 0.6 Height (m) 0.5 0.4 0.3 0.2 0.1 0 0.00 0.01 0.02 0.03 0.04 0.05 0.07 0.06…

A: The problem asks to identify and find the values of the quantity identified by the two lines. The…

Q: 5kN/m l l J 20meteor τι ι τ 1) Draw SFD and BMD. 2) Provide expressions for S.F and Bim e Calculate…

A:

Q: Storm Sequence Time units Precipitation (in.) Hydrograph Time units Flow (cfs) Time units Flow (cfs)…

A: Given  Effective precipitation= 1.5 in

Q: Find dimension A as shown in the figure below. Round answer to the nearest tenth. 425.0 260.00…

A: The dimension A can be calculated using simple geometry :  1) Hypotenuse Right angled triangle rule…

Q: A rectangular lot was measured using a 50m steel tape which was later found to be 15mm too short.…

A:

Q: PROBLEM 2: The L-shaped retaining wall shown retains soil on the right side and water on the left…

A:

Q: Convert the following to DMS, showing your work. Round to the nearest second. SHOW ALL OF YOU WORK…

A: Given data: angle θ = 3.06650 rad

Q: Determine the area bounded by a straight road and an irregular boundary using the data given below:…

A: The best method applicable for determination of area of irregular boundaries is Simpson's rule.…

Q: Two level sections of 35-m stations with center heights of 1.36 and 1.55 m in cut, base width 15 m,…

A: The distance between the two stations, L = 35m The base width, b = 15m The height at station 1 is,…

Q: Aerial photography is to be taken of a tract of land that is X-mi square. Flying height will be H ft…

A:

Q: Find the displacemnt value if work done is equal to 120 j and force applied on object 40 N

A:

Q: Survey Sarvey Targe Average value after CLR zero with multiple rounds Reading Average Valne after…

A: The angular measurement is the process of determining the direction of a line with reference to any…

Q: It is assumed that no mistakes exist, and that the observations have already been corrected for all…

A: The most probable value is given by, MPV=Sum of all valuesNumber of observations The value of ν is…

Q: Locate the centroid of the plane area shown if L = 126 mm.   the centroid of the plane area is: X…

A: There should be a range for answers. Please check onceI assumed square area as section 2 and…

Q: The following is a page of an old level field book, in which some of the missing entries are shown.…

A:

Q: -60 20 10 40 100- 10 -30 -15- 60

A: THE BASIC COMMANDS USED ARE 1. LINE 2. CIRCLE 3. OFFSET 4. XLINE 5. DIMENSION 6. LAYER

Q: 4. Every moming Joy walks to school from her boarding house and takes only a single route. For five…

A: GIVEN :- No. of paces on Monday = 345 No. of paces on Tuesday = 353 No. of paces on Wednesday = 358…

Q: What are the classifications of foundation

A: Foundation is the main component of a structure that connects the structure to the ground. The…

Length and Length related Variables

Length can de defined as the measurement or extent of physical quantities or objects from one terminal to another terminal. Stone age humans used finger length, step length, and so on to measure the size or displacement of an object. Nowadays, depending on how precise the measurement requires to be and the object’s size is measured, we use measuring devices for measurements like rulers and steel tape. Most people have used a ruler or tape measure to measure a particular distance or the size of an object. For more precise measurements of tiny objects, the development of measurement tools such as the Vernier caliper, which permits us to measure dimensions within 1/1000 of an inch. In the last few decades, electronic distance measuring instruments (EDMI) have been implemented that permit us to measure distances from a few feet to many miles with reasonable accuracy.