20. Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm. What is the maximum tension that can be exerted by the riveted strip if the shearing stress on the rivet is not to exceed 6.9 × 10' Pa ? Assume that each rivet is to carry one-quarter of the load.

20. Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm. What is the maximum tension that can be exerted by the riveted strip if the shearing stress on the rivet is not to exceed 6.9 × 10' Pa ? Assume that each rivet is to carry one-quarter of the load.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: 1. A steel rod (initial diameter: 3.2 mm, initial length: 42 mm) is extended by a uniaxial tensile…

A: Given: Steel rod diameter, D= 3.2 mm Tensile load, F = 4800 N'

Q: A child slides across a floor in a pair of rubber-soled shoes. The frictional force acting on each…

A: NOTE: As per bartleby guidelines we can answer only first question. For remaining questions please…

Q: A strand of dragline spider silk has a diameter of 6.0 μm, and can support a mass of 2.9 g.…

A: Required : Approximately how many copper wires would it take tosupport the same mass?

Q: A circular rod of cross-sectional area 2 x 104m² has a tensile force of 80 kN app The stress in the…

Q: A 100 N picture hangs from a nail in the wall. The diameter of the nail is 3.00 mm. The shear stress…

A: Write the given values with the suitable variables. F=100Nd=3 mm=3×10-3 m Here, F is the force and d…

Q: A 226-N object is hung from the end of a wire of cross-sectional area 0.03 cm-. The wire stretches…

A: Given: Force,F=226NArea,A=0.03cm2=0.03×10-4m2Length,L=150cm=150×10-2mChange in…

Q: What hanging mass will stretch a 2.0-mm-long, 0.59-mmmm-diameter steel wire by 1.2 mmmm ? The…

Q: The figure represents an insect caught at the midpoint of a spider-web thread. The thread breaks…

A: Given,breaking stress of the string, 9.2 ×108 N/m2strain, 2.00lengthh of the thread, L = 3.0 cmcross…

Q: A high-carbon steel wire, circular in cross-section, has a diameter of 14 mm. What is the force (in…

Q: The femur bone in a human leg has a minimum effective cross section of 2.85 cm² and an ultimate…

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…

Q: A metal slab of side (74+ 75) cm and thickness (74 + 25) cm is subjected to a tangential force of…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

A: Write the given values with the suitable variables. P=250 kN=250×103 Nb=0.12 md=0.05 mt=0.003 m…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A: To find minimum diameter for each rod use the formula of normal stress and put the values to solve .…

Q: ) A 54 kg diver is at the end of a diving board. That is 3.8 m long and has a mass of 26 kg. What is…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: To calculate the Young's modulus and the approximate yield strength for the material. Given data-…

Q: The screwgate carabiner is left open as it is loaded by a rope as shown. Calculate the stress state…

A: Stress is defined as force per unit area. σ=FA Where F is a force and A is cross-section area.

Q: A 557-N force is applied to stretch a cable, 66-m long and has a cross-sectional area of 2.8 mm^2.…

A: Given F=557 N L=66m A=2.8 mm2 Y=1.0x10^11 N/m2

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: Given, stress s=290×106 N/m2s=2.90×102×106 N/m2s=2.90×108 N/m2 strain ε=0.0040

Q: A vertical solid steel post of diameter d = 26 cm and length L = 2.70 m is required to support a…

Q: Mechanical engineering question. Need diagram and explanation. No chatgpt.

A: Step 1: Step 2: Step 3: Step 4:

Q: A punch for making holes in steel plates is shown in Fig. below. Assume that a punch having diameter…

A: Hence the answer..

Q: H.W/assume a leg has 0.6m shaft of bone with an average cross sectional area of 1.5 cm.What is the…

Q: A 10.2 m long wire with a cross-sectional area of 0.126 cm2 stretches by 0.196 cm when a tensile…

A: The given values are, L=10.2 mA=0.126 cm2=0.126×10-4 m2∆L=0.196 cm=0.196×10-2 mF=6250 N

Q: An aluminium (p = 2.7g/cm³) wire is suspended from the ceiling and hangs vertically. How long must…

A: Given that-Density of aluminium wire, ρ=2.7g/cm3Stress at upper end, σt= 8×107 N/m2We know…

Q: Assume Young's modulus for bone is 1.50 x 1010 N/m2. The bone breaks if stress greater than 1.50 x…

A: Given : Young's modulus for bone, Y = 1.50*1010 N/m2 Stress to break the bone, S =…

Q: A specimen with cylindrical shape was subjected to tensile test. Please plot the stress vs. strain…

A: We know, Stress= Weight/ Area Strain = Change in length/ (Original Length) Young Modulus = Stress/…

Q: Assume Young's modulus of a femure bone of an effective diameter 2.5 cm is 1.5 x1010 N/m2. The bone…

A: Given: A femur bone of an effective diameter 2.5 cm and it's Young's modulus = 1.5 × 1010 N/m2.…

Q: Two strips of metal are riveted together at their ends by four rivets, each of diameter 6.0 mm. What…

A: Given, Diameter of the metal bar, d = 6.0 mm = 6.0 × 10–3 mRadius, r = d/2 = 2.5 × 10-3 m Maximum…

Q: 216) What horizontal force must be applied to the cart shown in Figure -2, in order that the blocks…

A: Given Data ; The mass of the cart is given as M. The mass of block 1 is given as m1. The mass of…

Q: A solid copper cube has an edge length of 86.7 cm. How much stress must be applied to the cube to…

Q: A steel wire having a radius of 2.0 mm, carrying a load of 4kg, is hanging from a ceiling. Given…

Q: If the shear stress in steel exceeds about 4.00 x 108 N/m2, the steel ruptures. Determine the…

A: Given Maximum Shear stress = 4 × 108 N/m2 Diameter of cylinder = 2.5 cm We have to calculate…

Q: Humans can bite with a force of approximately 792 N. If a human tooth has the Young's modulus of…

A: Force exerted (F) = 792 N Cross sectional area (A) = 1.3 cm2= 0.00013 m2Length of bone (L) = 1.7cm =…

Q: A 406-N object is hung from the end of a wire of cross-sectional area 0.05 cm². The wire stretches…

A: The longitudinal stress on a wire is given by σ = FA, where F = the force acting on the wire and A =…

Q: A sphere of copper has a radius of 8.00 cm and is compressed uniformly by a force of 5.00 × 108 N.…

Q: the ankle joint therefore pushes upward on the bottom of the tibia with the force of 2800 N while…

Q: A 10.2 m long wire with a cross-sectional area of 0.126 cm? stretches by 0.196 cm when a tensile…

A: The young's modulus of the material is a fundamental property that depends upon the temperature and…

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

20. Two strips of metal are riveted together at
their ends by four rivets, each of diameter 6.0 mm.
What is the maximum tension that can be exerted by
the riveted strip if the shearing stress on the rivet is not
to exceed 6.9 × 10' Pa ? Assume that each rivet is to
carry one-quarter of the load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A rope of length 40.0 meters and 5.0 mm in diameter elongates by 1.0 meters when supporting a 50.0 kilogram mountain climber. What is the Stress and strain experienced by the rope?
Assume a person's mass is 62.0 kg and each of her shoes has an area of 220 cm2. F What is the compressive stress on her feet if her weight is A F spread out evenly over both soles of her shoes? 13.82 Ра A By what factor f does the compressive stress change if only 10.0 cm? of each shoe is in contact with the floor (as might be f = the case for high-heeled shoes)? * TOOLS x10
Humans can bite with a force of approximately 796 N. If a human tooth has the Young's modulus of bone, a cross-sectional area of 1.1 cm2, and is 1.9 cm long, determine the change in the tooth's length during an 7.96 ✕ 102 N bite. m
Assume that if the shear stress in steel exceeds about 4.00 x 108 N/m², the steel ruptures. (a) Determine the shearing force necessary to shear a steel bolt 1.40 cm in diameter. IN (b) Determine the shearing force necessary to punch a 1.25-cm-diameter hole in a steel plate 0.550 cm thick. N
80. Between each pair of vertebrae in the spinal column is a cylindrical disc of cartilage. Typically, this disc has a radius of about 3.0 X 10-² m and a thickness of about 7.0 x 10-3 m. The shear modulus of cartilage is 1.2 × 10' N/m². Suppose that a shearing force of magnitude 11 N is applied parallel to the top surface of the disc while the bottom surface remains fixed in place. How far does the top surface move relative to the bottom surface?
Question 7 of 10 What is the compressive stress ?/?F/A on a woman's feet, in units of kilopascals (kPa)(kPa) , if the woman's weight is spread out evenly over both soles of her shoes? Assume her mass is 66.0 kg66.0 kg and each shoe has an area of 215.0 cm2215.0 cm2 .
A vertical solid steel post of diameter d = 26 cm and length L = 2.70 m is required to support a load of mass m = 8400 kg. You can ignore the weight of the post. What is the stress in the post? Express your answer in pascals. What is the strain in the post?
Situation: A simply supported rectangular beam 400 mm wide having an effective depth of 550 mm carries a total factored load of 137 kN/m on a 6 m clear span. It is reinforced with 4914 mm² of tensile steel, which continues uninterrupted into the supports. Use f'c = 28 MPa. What is the factored shear at critical section? a. 616.50 kN b. 335.65 kN C. 541.15 kN d. 411.00 kN What is the Ultimate shear strength provided by concrete only? a. 148.4 kN b. 180.2 kN C. 178.1 kN d. 197.9 kN Throughout what part of the beam is web reinforcement is required? 3m 1.5 m c. 2.46 m d. 0.65 m a. b.
B8
Two strips of metal are riveted together at their ends by four rivets, each of diameter 8.0 mm. What is the maximum tension that can be exerted by the riveted strip if the shearing stress on the rivet is not to exceed 6.9 × 106 Pa? Assume that each rivet is to carry one quarter of the load.
Problem 2 P A 40 kips 30 in. 30 kips B 30 kips 40 in. Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P for which the tensile stress in rod AB is twice the magnitude of the compressive stress in rod BC.