20. Suppose a system has the following Bode plot. What is the transfer function of thy system? Magnitude (dB) Phase (deg) 60 40 20 0 -20 -40 55 -90 10-1 (a) G[s] = (b) G[s] (c) G[s] = (d) G[s] = 10⁰ (0.1s+1) s(0.001s+1) 10(0.18+1) s(0.001s+1) 0.1(10s+1) s(1000s+1) 10(10s+1) s(0,001s+1) Bode Diagram 10¹ 10² Frequency (rad/s) 10³ 104 105

20. Suppose a system has the following Bode plot. What is the transfer function of thy system? Magnitude (dB) Phase (deg) 60 40 20 0 -20 -40 55 -90 10-1 (a) G[s] = (b) G[s] (c) G[s] = (d) G[s] = 10⁰ (0.1s+1) s(0.001s+1) 10(0.18+1) s(0.001s+1) 0.1(10s+1) s(1000s+1) 10(10s+1) s(0,001s+1) Bode Diagram 10¹ 10² Frequency (rad/s) 10³ 104 105

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A parallel resonant circuit has a resistance of 2 k2 and half-power frequencies of 86 kHz and 90 kHz. Determine: (a) the capacitance (in nF) (b) the inductance (in uH) (c) the resonant frequency (in krad/s) (d) the bandwidth (in krad/s) (e) the quality factor
A series circuit consists of a reactor of 0.1 henry inductance and 5 ohms resistance and a capacitor of 25.5 μ F capacitance. Find the resonance frequency and the percentage change in the current for a divergence of 1 percent from the resonance frequency. [100 Hz, 1.96% at 99 Hz; 4.2% at 101 Hz]
Given range of frequencies for a channel (as shown in the figure) and SNR = 15, based on Nyquist's formula, how many signal levels are required? -3 dB 2 MHz 10 MHz
Start by finding the Thévenin equivalent circuit seen by the capacitance. Then, sketch the magnitude of the transfer function H(jw) = Vout/Vin. What is the value of the cutoff frequency?
Electrical Engineering will upvote . Need matlab knowledge these are the parts that need to be answered. ons: Calculate the cutoff points. Show a screenshot of your circuit. Are the calculated cutoffs being reflected on the theoretical Bode Plot? Include a screenshot of your codes and the theoretical Bode Plot with both cutoff points labelled. How well did the filter perform when processing the 10HZ and 15OHZ combined signal? Include a screenshot of the Scope. The transfer function for the band pass filter is given to you (equation 9). How was this derived? Show the steps starting from how you use the circuit to get the equations representing the circuit to how you solve the equations to get the final version. Given is that it is an RC Bandpass circuit with r1=10kohm, r2= 100kohm ,c1=1uf ,c2=0.001uf. the RC bandpass circuit proceeses 10hz and 150 hz combination. equation 9 needed for part 4 mentioned above is wC1 R Vw? (RCi+R1C2+R2C2)²+(1–w?C,C2R, R2)2 %3D
A parallel RLC resonant circuit has a quality factor Q-80, and a resonant frequency of 200 krad/s. Let R=4002, find the bandwidth of the circuit. OOOO 2000 2500 2400 None
The magnitude and phase diagrams are provided for a passive filter. Input signal vin(t)=15 cos(20000t+100°) V is applied. What is the output voltage in V when t-1ms ? Series RLC H(s) -20 -30 -40 700 10 10 180 150 ... ... ... ... 100 ... 50 10 10 Frequency (rad'sec) Phase (deg) Mag (dB)
Plot the magnitude and phase plot for the following transfer function, use the templates from the class notes module so as to provide somewhat an accurate representation of the magnitude and phase plots. H (ju) 10 jw (0.01jw+1) (0.1jw+1)
Find the transfer function for the circuit shown in figure 1. Plot the amplitude graph of 2logh10hw and the phase angle graph of H(jw)? Calculate the actual cutoff frequency? Calculate the true phase angle at the cutoff frequency?
Question 02: A) How do you use Kirchhoff's law? What are the limitations of Kirchhoff's law? B) What is resonance in RLC circuit? Define the Q-factor in RLC series circuit.
A Nyquist plot is obtained by plotting the amplitude (NOT in a log scale!) and phase (in degrees) of a transfer function in a single graph. Obtain the amplitude of the following transfer function at a frequency w = 5 rad/s G (jw) jw+a) Gw+2)Gjw+61(jw+c) Use the values: a=1.882, b=4.038 and c=6.433.
6 - Amplitude ratio of the output sinusoidal to the input sinusoidal is called .. O A) Root locus O B) Magnitude of the sinusoidal transfer function C) Phase angle of the sinusoidal transfer function O D) Magnitude of the Bode plot O E) Bode plot