20 MPa 60 MPa

Q: 60 N- m PROBLEM 3.12 Knowing that an 8-mm-diameter hole has been drilled through each of the shafts…

A: Diameter of hole = 8 mm Determine the shaft in which maximum shearing stress occur and magnitude of…

Q: Two solid steel shafts are connected by the gears shown. Knowing that for each shaft G= 11.2 * 106…

A: Given Data: The modulus of rigidity of the shaft is: G = 11.2 X 106 The allowable shear stress is:…

Q: Knowing that a given vertical shear V causes a maximum shearing stress of 50 MPa in a thin-walled…

A: Write the expression of the first moment of inertia for point A. Write the expression of the first…

Q: 60 N. m 1) Knowing that each portion of the shafts AB, BC, and 144 N m CD consist of a solid…

A: Given: Torque at position A is TA=48 N·m. Torque at position B is TB=144 N·m. Torque at position C…

Q: Under normal operating conditions, the electric motor exerts a 12-kip·in. torque at E. Knowing that…

A: Understand that the net torque on a cross-section is calculated by the sum of torques on any one…

Q: 60 mm 40 mm T.

A:

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A:

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, while sleeve CD…

A: (a)   Write the relation to calculate the inner diameter of the sleeve CD using the given diagram.…

Q: 22 mm For the cylindrical shaft shown, determine the maximum shearing stress caused by a torque of…

A:

Q: A torque T5 3 kN·m is applied to the solid bronze cylinder shown. Determine (a) the maximum shearing…

A: Given data :T=3 KN.mL=200 mma) Max. shear stress will occur on surface of shaft .    ζmax=T205…

Q: Determine the maximum torque of the tube shown if the allowable shearing stress is 46 Mpa. Given: t…

A: Given data:allowable shear stress = 46 MPat = 2.73 mma= 33 mm

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: Given: The allowable shearing stress in the shaft, τ = 55 MPa The length of shaft AB, LAB = 750 mm =…

Q: The steel jacket CD has been attached to the 40-mm-diameter steel shaft AE by means of rigid flanges…

A: Given Data: The outer diameter of the jacket is D = 80 mm. The thickness of the jacket is t = 4 mm.…

Q: Determine the range of values of σx for which the maximum in-plane shearing stress is equal to or…

A: Step-1 Given: The normal stress on the vertical plane is σX. The normal stress on the horizontal…

Q: Two solid shafts are connected by gears as shown and are made of a steel for which the allowable…

A: Given, dBC= 1.6 in dEF= 1.25 in

Q: Under normal operating conditions, the electric motor exerts a 12-kip·in. torque at E. Knowing that…

A:

Q: Shaft AB is made of a steel with an allowable shearing stress of 90 MPa and shaft BC is made of an…

A: Given that ;          Allowable shearing stress of steel τAB =90MPa…

Q: The steel pipe AB has a 102-mm outer diameter and a 6-mm wall thick-ness. Knowing that arm CD is…

A: Given, Outer diameter (do)=102 mm Internal Diameter (di)=do-2×wall thickness= do- 2×6=102-12=90mm…

Q: 5) Knowing that an 8-mm-diameter hole has been drilled through each of the shafts AB, BC, and CD,…

A: The stress which is induced in a shaft due to torque or twisting moment parallel to the…

Q: Knowing that an 8-mm-diameter hole has been drilled through each of the shafts AB, BC, and CD,…

A:

Q: For the state of plane stress shown, determine the largest value of σyfor which the maximum in-plane…

A: Given: σx=60 MPaτxy=20 MPaτmax=75 MPa

Q: 3. For the state of plane stress shown, determine the largest value of oy for which the maximum…

A: Given Data⇒ Maximum in-plane shearing stressζmax=75 MPa Problem statement⇒ Problem says determine…

Q: 40 MPa 35 MPa For the given state of stress, determine (a) the orientation of the planes of maximum…

A:

Q: A rectangular key was used in a pulley connected to a line-shaft with a power of 125 kW at a speed…

A: Power, P= 125 kW= 125000 W Speed, N= 900 rpm= 900/60 rps Shear stress of the shaft, τshaft= 40 N/mm2…

Q: Determine the largest allowable diameter of a 10-ft-long steel rod (G= 11.2 × 106 psi) if the rod is…

A: Given: The length of the steel rod is L=10 ft. The shearing stress in the steel rod is τ=12 ksi. The…

Q: 2. Shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB…

A: 1. Problem statement: To find the minimum and maximum shearing strength in the shaft BC and…

Q: Two solid steel shafts are fitted with flanges that are then connected by bolts as shown. The bolts…

A: T=TAB,LAB=0.6mmc=12d=302=15mmJAB=π2c4=79,481.25mm4φB=TABLABG.JABTAB=G.JABφBLAB=77×109×79481.250.6φB…

Q: PROBLEM 3.11 Knowing that each portion of the shaft AD consists of a solid circular rod, determine…

A:

Q: 3.42 Two identical metal sheets are formed into tubes with the circular and square cross sections…

A:

Q: The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve CD…

A: Given data as per question Shear stress in solid spindle =12 ksiShearing stress of sleeve=5.8…

Q: A torque of 10kN-m is to be carried by a flanged bolt coupling that consists of eight 10mm diameter…

A:

Q: For the state of stress shown, determine the maximum shearing stress when (a) ơ, = 0, (b) ơz = 60…

A: σavg=1230+100 =6512σx-σy=1230-100=-35

Q: For the state of plane stress shown, determine the maximum shearing stress when (a) o, = 14 ksi and…

A:

Q: Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A…

A: Given Data Modulus of rigidity of cylinder AB is : Galuminum =26 GPa=26×103 MPa Diameter of…

Q: Shaft BC is hollow with inner and outer diameters of 90 mm and 120 mm, respectively. Shafts AB and…

A: Find, 1-Maximum shear stress and minimum shear stresse in BC shaft  2- diameter of AB or CD

Q: 3. The solid spindle AB is made of a steel with an allowable shearing stress of 12 ksi, and sleeve…

A: a) Calculation for sleeve CD: (C2)Radius=12*3 inch=1.5 inch C1=C2-t=1.5-0.25=1.25 inch

Q: Two solid steel shafts are fitted with flanges which are then connected by fitted bolts so that…

A:

Q: Q 3: -Knowing that the bracket AB has a uniform thickness of 3 kips 0.75 in. in., determine (a) the…

A:

Q: For the gear train shown, the diameters of the three solid shafts are: dAB = 20 mm, dco = 25 mm, dgf…

A:

Q: 1. The aluminum shaft shown has a constant diameter, with 1000 N-m applied at gear A, 1200 N-m…

A: Given:TA=1000 N.mTB=-1200 N.mTc=800 N.mTD=-600 N.mζ=25 MPaθ=4°

Q: 3.7 The torques shown are exerted on pulleys A, B, and C. Knowing that both shafts are solid,…

A: Consider shaft AB Let TAB be the torque in the shaft AB if a section is passed through shaft AB…

Q: Knowing that the internal diameter of the hollow shaft shown is d = 0.9 in., determine the maximum…

A: Given data  outer dia of hollow shaft (do) = 1.6 in. inner dia of hollow shaft (di) = 0.9 in. torque…

Q: Knowing that an 8-mm-diameter hole has been drilled through each of the shafts AB, BC, and CD,…

A:

Q: A torque T = 1500 N – m is applied to the hollow shaft shown that has a uniform 10 mm wall…

A: find shear stress at point a and b and angle of twist.

Q: two solid shafts are connected by gears as shown A toque of magnitude t=900N.m applied to shaft AB…

A:

Q: etermine the maximum shearing stress (MPa) in a solid shaft of 60-mm diameter as it transmits 91 kW…

A: Given:Diameter, d=60mmPower, P=91KWspeed , N=175rpm

Q: Determine T max for a 40-mm diameter shaft if the allowable shearing stress is equivalent to 80 mPa

A:

Q: 4. The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A…

A:

Q: Knowing that the internal diameter = 12mm and the torque magnitude = 1.35kn.m. Determine the maximum…

A:

Q: 9. Two wooden members of uniform rectangular cross section are joined by the simple glued scarf…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.