20 kg A TW S B 10 kg PROBLEM 13.19 The system shown, consisting of a 20-kg collar A and a 10-kg counterweight B, is at rest when a constant 500-N force is applied to collar A. (a) Determine the velocity of A just before it hits the support at C. (b) Solve part a assuming that the counterweight B is replaced by a 98.1-N downward force. Ignore friction and the mass of the pulleys. VA = 3.16 m/s VA = 5.48 m/s

20 kg A TW S B 10 kg PROBLEM 13.19 The system shown, consisting of a 20-kg collar A and a 10-kg counterweight B, is at rest when a constant 500-N force is applied to collar A. (a) Determine the velocity of A just before it hits the support at C. (b) Solve part a assuming that the counterweight B is replaced by a 98.1-N downward force. Ignore friction and the mass of the pulleys. VA = 3.16 m/s VA = 5.48 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 38-lb collar A is released from rest in the position shown and slides up the 30° inclined bar with negligible friction due to the action of the constant force P = 45 lb applied. on the wire.Assuming that the maximum deformation of the spring is 6 inches, determine b) The required stiffness K of the spring, in lb/ft. The position of the small pulley B is fixed.
IV. For the following system that starts from rest, the spool has a weight of 300 N and a radius of gyration ke = 0.3 m, and block A is attached to it as shown of weight 200 N. A constant horizontal force F is applied to the cord in order to give the block an upward speed of 5 m/s. (Neglect mass of cord and tension force). -F 1. Draw the free body diagram of the system. 2. Calculate the angular speed of the spool at t= 6 seconds. 3. Calculate the vertical reaction force at the pin at t= 6 seconds. 4. Calculate the horizontal force F.
A 10-lb bock is resting on an inclined surface at an angle of 30°, as shown. The block is in contact with a compressed spring that has a modulus of 75lb/in. The spring has an initial compression of 6 inches that is released by cutting the restraining cords. If the coefficient of kinetic friction between the inclined surface and the block is 0.15, determine the speed of the block as it leaves the spring. Position B L. Position A Position C 6 in, Restraining cords ww. H = 0.15 k = 75 lb/in 30°
Disk "A" of weight 5 lb and radius "r=3 in" is at rest and placed in contact with a belt which moves at a constant speed of 57 ft/s. Hk = 0.20 between the disk and the belt. a) USING THE PRINCIPLE OF LINEAR AND ANGULAR IMPULSE AND MOMENTUM, draw the FBD for the before, impulse and after case.
Activity 3. A body that weighs W Newtons falls from rest from a height of 600mm and strikes a spring whose scale is 7.00 N/mm. If the maximum compression of the spring is 150 mm, what is the value of W? Disregard the mass of the spring. (Ans. W=105 N) 600mm 150mm
In the system shown, a 150 N collar-pulley assembly slides on a horizontal shaft with coefficient of kinetic friction uk =0.10 between the collar and the shaft, and is acted upon by a force P with a magnitude of P = 250N at an angle 0 = 30 as shown. Knowing that the assembly is initially at rest, what is the time when the velocity of collar B reaches to 3 m/s? Also, at this instant, find the tensile force in the cord and the velocity of block A.
Block A (99-lb) is attached to block B (49-lb) through the interconnected pulleys C and D, as shown in the figure above. The coefficient kinetic friction between block A and the incline is 0.2. If block A has now a speed of 5(ft/s) down the incline, then while neglecting the mass of pulleys and ropes, Determine: 1. The Acceleration of block A 2. The distance (magnitude and direction) block B moves as block A slides to a stop.
3. A 10.0-kg block is released from point A on a track ABCD as shown. The track is frictionless except for the portion BC, of length 6.0 m. The block travels down the track and hits a spring with a spring constant of 2250 N/m and compresses it a distance of 0.30 m from its equilibrium position before coming to a stop momentarily. Determine the coefficient of kinetic friction between the track portion BC and the block. 3m 6 m- wwwwwww
A car of mass 700 kg travels round a horizontal curve of 60 m radius. The centre of gravity of the car is 1.25 m above the ground and the distance between the wheels is 1.7 m. If the limiting coefficient of friction between the tyres and the road is 0.6 determine, with reason, whether the vehicle will skid or overturn when rounding the bend at speed. Hence state the maximum permissible speed to navigate the curve safely.
Problem 1. A 35-lb block slides down a 20° inclined plane with an initial velocity of 3 ft/s. Determine the velocity of the block in 4 seconds if the coefficient of kinetic friction between the block and the plane is 0.29.
An object of mass m1 slides on a sloped block of mass M2, which in turn slides on a horizontal surface. The slope angle is a constant 3, and both masses are initially at rest. There is no friction between any of the objects, and the masses are subject to the force of gravity -mgêy. Use as co- ordinates the horizontal position x2 of mass m2, and the height y1 of mass m1, as shown in the y4 Y1 M2 x2 diagram to the right. Find the equation of motion of block 2, ä2(t). The expression should only include expressions involving constants: M2, m1, g, and B.
2- The two blocks shown are originally at rest. Neglecting the masses of the pulleys and the effect of friction in the pulleys and assuming that the coefficients of friction between block A and the horizontal surface are u, = 0.25 and uk = 0.20, determine (a) the acceleration of each block, (b) the tension in the cable. 30 kg 25 kg