2.During the brick compressive test, failure load is 183 kN under immersion saturated state, and 207 kN under dry condition (compression area 115 mm × 120 mm), whether this kind of brick is suitable to be used within water?

Q: 3.0000 R2.0000 1.0000 4.0000 2.0000 4.0000 4.0000 0000 0000 0000-

A: Handmade drawing are attached for better understanding.

Q: Please explain how to do the marking for 30°incline plane, C4 x 4 and the center for M10 x1.5 on a…

A:

Q: SB0°53E A IDI N18°39'E

A: Bearing of line AB= S 80°53'EBearing of line DA= N 18°39'E        AD= S18°39' W∠A= 80°53'+18°39'=…

Q: Missing data Length Bearing АВ 102.84 N 54d 47m E BC ? S 44d 46m E CD 77.25 S 54d 21m W

A:

Q: Compute the interior angle at A, B, C, D Answer only

A: Interior Angle at 'B' = 137⁰35⁰

Q: Determine the x-coordinate of the centroid of the shaded area. y x=ky a O A. 3b/10 O B. 2b/7 OC.…

A: To find x - coordinate of centroid

Q: All data are in feet. The elevation of BM-A is 1364.58 feet. Rod readings are as follows: +S on…

A:

Q: bridge located 145 m beyond station 14+00 should be   A. 01+45 B. 15+45 C. 145+35 D. None of the…

A:

Q: Q3) In closed traverse ABCD show below:- 1-Correct the External angles if the instrument accuracy…

A: Given data  The bearing of Line AB θAB=120°  The external angle at A, θAE=272°47'15" The external…

Q: Find intermidiate elevation

A: ###Finding Elevation of Intermediate Point C ###

Q: INSTRUCTIONS: (USE METHOD OF SECTION) A. Determine the forces in all members with () marks of the…

A: Given a truss where only few member forces are to be found Since only few member forces are to be…

Q: Find the centriod

A:

Q: 12. Given the following tabulated data for a closed tra- verse in which the lengths of sides CD and…

A: to find- length CD and DE for given traverse data.

Q: C The Expressions For The Steady-state Voltage And C... | Chegg.com Syllabus Scores Text Study Area…

A:

Q: 3. Complete the calculations tabulated below. Perform a check on the ending elevation of BM 3055.…

A: Solution:- The complete calculation is shown below in the table.

Q: Given the following information Distance Azimuth (m) Course Bearing Latitude Departure N 60°00' W…

A: Answer:- Latitude and Departure:

Q: Which Data Collector sequence of screens brings you to the Offsets options menu? SeheBacksightSet…

A: Note - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: What is the deflection angle at A?

A: Deflection Angle: It as an angle made by succeeding line (AB) with prolongation of preceding line…

Q: P7-9 Go to www.pearsonhighered.comica ars resources, navigate to this textbook and chapter, and…

A: I have solved in great detail and also give the background concept to change azimuth to bearing plz…

Q: A closed traverse has the following data: LINE AB BEARING BC CD DE EA DISTANCE (m) 60.00 72.69 44.83…

A: Line Bearing (B) Distance (m) Latitude (L.CosB) Departure (L. SinB) AB B1 60.00 60.00 (Cos B1)…

Q: Part A) Balance the angles Part B) Compute the bearings for all sides Part C) Compute latiudes and…

A: since , you have posted question with 4 subparts ,I have solved 3 parts and if you want the answer…

Q: LINE AB BC CD DE EF FORWARD BEARING N 44°38' E S 42°30' W N 22°35' W BACK BEARING N 42°30' W S…

A: Bearing of AB= N44°38' E         Azimuth of AB= 44°38' Bearing of BC= S 42°30'E      Azimuth of BC=…

Q: The total station instrument requires a barcoded staff to allow measurements. O a False O b. True

A: The total station instrument requires a barcoded staff to allow measurements. Given Statement is…

Q: 6.29. The flowrate passing over this sharp-crested weir in a channel of 1 ft width is 3.5 cfs.…

A: Given  figure are:- As, we know that force exercted by the water on weir plate F =ρw·g·A·h' here ,…

Q: 9. RISE AND FALL METHOD. Given rangement of lines for a ievel route run from BM-1 to in which…

A: In surveying when with help of any leveling tool we measures the level of station then to find the…

Q: STA BM1 ТР1 ТР2 BM2 BM3 TP3 BM4 ТР4 ТР5 TP6 BM5

A:

Q: Find headlight sight distance and intermediate sight distance for V=70kmph. (Hint: f=0.36,t-2.5 s,…

A:

Q: of

A:

Q: How was the sum of  angles received? How was the closure error calculated?

A: Given: 3 angles of a triangle  Required: Calculate sum of measured angle and also find closure error…

Q: GIVEN THE PROFILE SHOTS, COMPLETE THE TABULATION AND DRAW THE CROSS-SECTIONAL ELEVATION FROM BM1…

A: To find: elevation of different point Cross sectional elevation

Q: Compute the distance of the missing side and compute the bearing of the missing side

A:

Q: Fom the following traverse notes, determine the linear error of closun NE BEARING LENGTH -2 N 73°…

A:

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+3+3=9

Q: Determine static indeterminacy

A: Given data : Total number of external support reaction (R)=3+3+3=9 Number of member (m)=3 Number of…

Q: Item Answer Length of connecting line Bearing of connecting line Length of BC Bearing of DA

A:

Q: Obberved beaning computer Correstien Adjusted values Internal Porward BacK angle Beaning Begring…

A:

Q: Profile Level Notes: The elevation of BM A = 533.00' BS (plus sight) on BM A = 6.91' IFS (minus…

A: To Determine :- Elevation of the STA 1+50 Concept :- HI = Elevation + BS Elevation = HI - IFS…

Q: Item 9 ▼ Part A What error results on a 200-ft sight with a level if the rod reading is 11.307 ft…

A: Observed length of rod = 11.307 ft Out of plumb distance= 0.30 ft

Q: the mea- 4. DEFLECTION sured 152°18'R, TRAVERSE. The following are angles for 22° 15'L, ANGLE a…

A: Measure angle for closed traverse -  1st angle - 97°05' 2nd angle -152°18' 3rd angle -96°13' 4th…

Q: Draw the cross sections and compute V. Two level sections of 40-m stations with center heights of…

A:

Q: Ä = instrument set up,   TP = turning point,  HI = elevation of line of sight

A:

Q: Text Book answer is 19.62Kn,45.78Kn and 6.54 Kn

A: Concept and the formula are correct.here the expert has done calculation mistake.  Mass = 400000 kg…

Q: = Find the centroid of the next shaded area. 6m

A:

Q: Please check if this is correct because the angle given is 30 degrees, not 60 degrees.

A: Check whether taken 60° angle is correct or not.

Masonry wall construction

Masonry walls of various sorts are utilized in building construction. Masonry walls are the most enduring feature of any structure or building. It separates a structure from the outside world. In masonry construction, the common masonry materials used are building stone, brick, cast stone, glass block, and concrete block. Masonry construction is a type of construction that has the highest durability.