2.Compute the efficiency of the Combustion Chamber and the thermal efficiency of a Gas Turbine Power Plant, if the actual heat released by the gas is equal to the heat supplied to the plant is 1,042 Joules and if the thermal efficiency is 20% less of that efficiency in the chamber. What is the net work produced if the theoretical heat value available of the fuel is 1,215 joules?

2.Compute the efficiency of the Combustion Chamber and the thermal efficiency of a Gas Turbine Power Plant, if the actual heat released by the gas is equal to the heat supplied to the plant is 1,042 Joules and if the thermal efficiency is 20% less of that efficiency in the chamber. What is the net work produced if the theoretical heat value available of the fuel is 1,215 joules?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the following: a. Enthalpy of the steam in kJ/kg entering the condenser b. Enthalpy in kJ/kg of the condensate c. Enthalpy in kJ/kg of the feed water
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 11. Calculate the thermal efficiency of the cycle
6. A 600-MW coal electric power plant substitutes 8% of its fuel with "tree clippings," which are tree branches that are cut to clear roads as well as the access lanes (rights of way) of power lines. The tree clippings are fed in the boiler together with the coal. How much coal is saved annually by this practice and how much CO₂ emissions are prevented?
5. In an ideal Otto Cycle, the pressure at the beginning of the compression process is 15 psia, the temperature is 70F and the volume is 13.08 cubic feet. The maximum temperature of thre cycle is 2804F, and the heat supplied is 372 BTU. Using constant specific heat, calculate: a. The temperature at the beginning of the combustion, Rankine b. The compression ratio c. The temperature at the end of the expansion process in Rankine d. The net work of the cycle in BTU e. The thermal efficiency of the cycle in percent
Show all elements of your design including the design calculations for the problem: When heating up a cold stream (5000 kg/h water) from 40ᵒC to 90ᵒC while cooling down a hot stream (5000 kg/h water) from 110ᵒC to 60ᵒC in AES exchangers, how many shells do you need?
!
If one mole of air (rigid diatomic gas) is initially at 20 ◦C, is compressed and expanded 7-fold as part of the Diesel cycle, and 4 kJ of heat is generated as a result of the fuel injectionand combustion, calculate: (i) the temperature after each stage of the Diesel cycle; (ii) the heat absorbed/expelled during each stage of the cycle; and (iii) the efficiency of the Diesel cycle.
Steam from a turbine with inlet pressure 30 bar and temperature 350°C is bled at 5 bar and 1 bar to supply a two-stage regenerator to heat up condensate leaving the turbine at 0.08 bar. In each stage, the condensate is heated up to the saturation temperature of the bled steam and the bled steam itself condenses completely. Remember: in a regenerator, there is no contact between the two streams, only heat exchange. of Consider the amount of steam bled at 5 bar and 1 bar, respectively, to be m¡ and m2 kg per steam supplied to the turbine. For the first stage, m¡ kg of bled steam at 5 bar heats each kg of condensate arriving from the second stage without any contact (that is, regeneration). Then, m¡ kg of condensate derived from the bled steam drains into the steam space of the second stage at 1 bar without heat loss. The combined drain from the second stage at 1 bar consists of mi+m2 kg per kg of steam supplied to the turbine. The combined drain is cooled to the condenser temperature…
Discuss any present applications of , and future prospects for, vapor-cycle engines using fluids and other than water.
A nuclear-power station with a life of 25 years produces 750 MW per year as usefulenergy. The energy cost is as follows:150 MW lost in distribution20 MW needed to mine the fuel50 MW needed to enrich the fuel80 MW (spread over 25 years) to build the plant290 MW lost as heatWhat is the efficiency of the plant? What is the efficiency of the system (including distribution losses)?
A boiler furnace releases 10 400 kj of heat for each kg of fuel burned and produces dry staturated steam at 14000 kpa from feedwater at 200 degrees celcius . How many kg of steam will be produced for each kg of fuel burned if the boiler had an efficiency of 66% ? .
1. Determine the Rankine efficiency of a condensing steam turbine operating in a Rankine cycle as follows: Steam pressure - 200 psiaSteam temperature - 1000 FExhaust pressure - 2 in Hg absoluteSteam rate - 1.5 lb/kW-hr 2. If the no. 1 problem has a thermal efficiency of 30%, how many barrels of 30 °API fuel oil will be required to produce 1000 kW-hr of power. Neglect the pump work.