2.9 For an LTI system, the impulse response is h(t) = e¹u(t). If the input to the system is x(t) = 10e-2¹u(t), find the output y(t).

Q: Explain the operational process of Chemical Vapor Disposition (CVD) in fiber optic cable…

A: Chemical vapor deposition is a process that involves the reaction of a volatile precursor which is…

Q: Explain the disadvantages of digital telecommunication.

A: Digital communication : This is a process in which transform the information by using device that is…

Q: swer the following questions: State two advantages of the “orthogonal least square (OLS)' method in…

A:

Q: What are Hall probes and how they work?

A: A Hall probe is a tool that uses a calibrated Hall effect sensor to measure a magnetic field's…

Q: What the Working principles of Telephony with figure, photos, tables and video

A: Once your call has been answered, you speak into the mouthpiece of your phone. Your voice generates…

Q: Q3: Assume a DM system that can only process analog information signals with a 3.5 kHz bandwidth.…

A:

Q: poles ying unit step input, gain of 34. IA hes has system yotem has of yce) and if at ー4 - b. the…

A:

Q: Why does base bias produce such an unstable Q point?

A: According to the question we have to discuss, why does base bias produce such an unstable Q point?

Q: Explain the function of a repeater in a communication system.

A: A repeater is an electrical device used in a communication system that receives signals and…

Q: communications systems question :- What is the meaning of the following abbreviations : PAM, PDM,…

A: Given abbreviations is used for different modulation techniques. PAM is known as pulse amplitude…

Q: When a processor responds to a RQ/GT0, the value of MN/MX would be __________________ a. 1 b. 0 c.…

A: The explanation is as follows.

Q: Explain block schematic of TDM?

A: Time division multiplexing is a technique by which multiple data signals can be transmitted over a…

Q: 03: Assume à DM system that can only process analog information signals with a 3.5 kHz bandwidth.…

A: Digital communications

Q: Given A = and B = Determine the dot product of A and B. (Round your answers to 4 decimal places.)

A: There are quantities which are AC and DC . The magnitude of DC quantities is constant. AC quantities…

Q: Match the signal state with its description. READY=1 A. The MPU has put valid data on the bus B.…

A: Here in left side specific signal is given in which * indicates the active low signal means it can…

Q: 3- Draw the Experimental setup of the short- circuit Test.

A:

Q: 6) Write the function for Em(13,36,68). Then draw circuit by using AND, NOT, OR gates.

A: Given Boolean function fa,b,c,d,e,f,g=∑m(13,36,68)

Q: Q5. Explain each line in Verilog code bellow. In this code what does module, input, output, wire,…

A:

Q: Why we use FT-IR instrumentation?  Please shortly answer at your own words.

A: The explanation is as follows.

Q: Built a 50V DC power supply using. (i). Capacitor input filter. (ii). Choke input filter. Note: AC…

A: To build a 50V DC power supply using a capacitor input filter and a choke input filter, we will…

Q: 1ssignment: Given: 6 = 100 si { 200N Find: a) Ays= Vo Vs Vo io E b) Ais= io is c) ac vollage @ each…

A: Resistance is a degree of the insurance from stream in an electrical circuit. A capacitor is a…

Q: In time the use of the ________ became the more desirable approach because an important parameter of…

A: There are few parameters which has different applications and their different advantages. Some of…

Q: (a) Describe a time response analysis in a control system. (b) Determine the condition of time…

A:

Q: This is third time that I post it all the given answers are chat gpt or ai was totally wrong. Needs…

A: Superconductivity is a quantum mechanical phenomenon where a material, at very low temperatures, can…

Q: describe how TDM works?

A: Antenna- An antenna is a structure made up of metal which captures or transmits radio…

Q: Implement 8-bit asynchronous ripple counter and showing truth table, timing diagram. Also show how…

A: According to the question, we need to implement an 8-bit asynchronous ripple counter and showing the…

Q: In a real world application, any signal will produce a noise as shown in Figure 2. In your opinion,…

A:

Q: Analysis of Dispersion Compensation Techniques Used in Optical Fiber Communication

A: We need to Analysis of Dispersion Compensation Techniques Used in Optical Fiber Communication.

Q: Why we use the modulation ?

A: The explanation is as follows.

Q: How does the modulation technique used in analog and digital communication affect the transmission…

A: Modulation is a technique used in both analogue and digital communications to transmit signals over…

Q: Data communication subject , i need now fast less than 5 m

A: In this question we will write about balanced modulator...

Q: rect(f) 47 rectlt) = - 4 4 2 €7 a12 11.14 rectlt) ya -a/2 rect (t) → must have unit area tep Ult) >…

A:

Q: Give the reason for the following statements: 1) Using a Venturi flow sensor makes the measurement…

A: Any liquid coulmn upto a certain height has some potential energy. Venturi flow meters are devices…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.