A 2.2-lb steel tape is 99.98 ft long at 68° F while supported for its full length with a 10-lb pull. It hasa cross-sectional area of 0.005 sq in. and E= 29 x 106 psi. The tape held horizontally, supported at itsends only, and pulled with a force of 25-lb. The distance measured is 3500.50 ft under thetemperature of 83° F. Determine the correct distance (Consider Temperature, Tension and SagCorrection ONLY). You must provide solutions to support your answer.FormulaCtemp = 0.00000645 x (T-68°F) x L, Ctension = (P-Ps)L/AE, Csag = - W² x L / (24 x P²)(Cslope = -(S)² / (2 x L), )where, T = temperature, L = Tape length, S = slope, W = weight of tape, P = applied tension, P, =standard tension, A = cross-section area

Answered: Image /qna-images/answer/5ef0e5f5-bef9-44aa-a904-73a31e1784b2.jpg

Answered: 2.2-lb steel tape is 99.98 ft long at…

Engineering

Civil Engineering

2.2-lb steel tape is 99.98 ft long at 68° F v

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Calculate the fixed-end moments for beam due to unit displacement at its left support. Diagram:…

A: Given: Moment at support A= MA Reaction at support A= FA Moment at support B= MB Reaction at support…

Q: Time (hrs) 0 12 24 36 48 60 72 84 96 108 Inflow Discharge (m3/hr) 20 191 249 164 110 82 62 48 32 28…

Q: What is profile leveling and what is the purpose of profile leveling?

A: Given question has two parts (1) what is profile levelling? (2) what is the purpose of profile…

Q: The beam supports a distributed live load of 1.5 kN/m and single concentrated load of 8 kN. The dead…

A: Given data in question Load 8 kN live load Dead load 2 kN/m 1.5 kN/m live load To find out…

Q: A rod of length 150 cm and of diameter 2,0 cm is subjected to an axial pull of 20 kN. If the modulus…

Q: Station BM20 TP1 TP2 TP3 BM20 BS (m) 26.921 26.733 26.615 26.648 HI (m) FS (m) 27.235 27.018 26.581…

Q: Part 2: A girder shown below in figure 1 is subject to the following concurrent forces acting at…

Q: 3. For the cantilever beam and loading shown, determine the following using double integration…

Q: Design a tension member that consists of two C15 channels and two PL 1/2 x 16, arranged as in the…

A: Given data: Two C15 channel sections and two PL 1/2*16 plates Dead load=PD= 300 k Live load=PL= 450…

Q: If the load factor of a section is 3 and the shape factor is 2, then the factor of safety to be…

A: Given data :- If the load factor of a section = 3 Shape factor = 2 To calculate the factor of safety

Q: If it is known that the center pin A supports one-half of the vertical loading shown. 6 panels at 12…

Q: The (X,Y) coordinates (in feet) for a closed-polygon traverse ABCDEFA follow: A (460.88, 139.31), B…

Q: A reservoir has average surface area of 20km². Mean rate of inflow is 10 m²/S mean outflow is 15…

Q: For Unsteady Flow Orifice, derive the formula in solving As in terms of h for the cross-section of…

A: For Unsteady Flow Orifice, derive the formula in solving As in terms of h for the cross-section of…

Q: Mat foundation (20 x 30) is built on a sand layer with an internal friction angle of 32 degrees and…

A: Answer We know that Vesic's bearing capacity equation is given by q = C' Nc sc dc ic + γ*df*Nq sq dq…

Q: 3 b S C Maxximum Flow Inspection of a free way, data set record of Cokm/hr, Jam of densita of of…

Q: (a) Draw qualitatively the deflection curve based on the bending moment diagram. (b) Determine the…

Q: 2. Compute the maximum shear stress and maximum STRESSES flexural stress of the beam shown in the…

Q: A force of 68.5 kN acts at location with an eccentricity of 25.1 mm from the centroid of the beam…

Q: Determine the slope (in rad) at 3.3m from the left if P = 249kN, E = 25000MPa, and I = 223x105mm4.…

Q: The trap door is held open by the rope AB. If the tension in the rope is T = 70 kN, determine its…

A: T=70kN To find moment about y axis

Q: With aid of diagram, elaborate on the method to test material hardness using Brinell hardness test

A: Brinell hardness test:- The Brinell hardness test is a common method used to determine the hardness…

Q: A helical spring is fabricated by wrapping wire 25mm in diamet around a forming cylinder 250…

Q: Two circular shafts are joined together between fixed supports to resist a torsional moment of 80…

A: Given SteelHollow circularDo=100mmDi=80mmG=150GPa AluminiumSolid circularD=75mmG=70GPa To Find…

Q: What are the types of loads on structures?

A: Structure is an assemblage of load carrying members such as footing , column, beam, slab and wall.

Q: m- A-36 steel rod is subje shown. Determine the displacement of end A with 30 kN 30 A 400 mm B 4 5…

Q: C 5 kN 45° A B D 1 m 45° -2 kN F 1 m E Determine the magnitude of the force (in kN) in member BE.…

Q: A.Assuming a 40 hour work week for 50 weeks per year, what is the loaded labor cost per hour for the…

A: Given data: Fire partition = 10’ tall and 20’ long Base salary = $13.45 per hour FICA = 6.8% of…

Q: Excavation was being carried out for a foundation on plastic clay with a unit weight of 22,5 kN/m³,…

Q: Q7. Use the method of conjugate beam to find the slope and defection at a distance of 2m from the…

A: Given Data IAB = 5000 cm4 Determine the slope and deflection at 2m from free end using Conjugate…

Q: 120 N.m A 300 60° 200 B 400 E 300 200 Dimensions in millimeters 600 N y G Determine the magnitude of…

A: y- component at E

Q: What are the units for the -0.7295 and 1.333?

A: This question is related to the Engineering Mechanics from Civil Engineering. This question is…

Q: Solve the following reactions

Q: C3. What is the support reaction at point B? a) 36 kN b) 18 kNm c) 12 kN c) 36 kNm 2 m A 8 kN/m 3 m…

A: Given, Udl = 8 kN/m Total span = 7m

Q: Give the graph please solve the following. 1. What are the elasticity moduli of Materials A and B,…

A: Given:- The stress-strain graph for the two materials is given For material A, the equation for the…

Q: A beam fabricated from western white pine has been reinforced by bonding steel strips on its top and…

Q: Problem 2 The unbraced column length of Round HSS 16 x0.625 in A500 Grade B (Fy = 46 ksi) is 27 ft.…

A: Given:- The unbraced column length = 27 ft The yield strength of the steel (fy) = 46 ksi The steel…

Q: Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice…

A: A tensile force, P = 11kN is acting on a rectangular cross-section of 150mm x 75 mm. To determine…

Q: Benkelman Beam deflection analysis was carried out on 10 selected points of a flexible pavement…

Q: For the following wastewater and biomass characteristics: Q0 = 50 m3/d S0 = 60 mg NH4+-N/l Xi0 = 20…

Q: A slab panel in a building is idealized as cantilever beam as shown below with their ustimate…

Q: Dimensional analysis shows that for wind alone, the nondimensional ventilation rate for a given…

A: Given: Non-dimensional ventilation rate for a given building is a function of Reynolds number.…

Q: Qus: In a plate load test bearing plate size which is recommended is : 1. Minimum 30 cm, maximum 75…

A: First we summarise the given data : In a plate load test bearing plate size which is recommended is…

Q: Question 2 (b) Using the same problem above. Compute the location in m of the hydrostatic force from…

Q: An infinitely long slope is made up of a c-ôsoil having the properties: cohesion (c)=20 kPa, and dry…

A: Given: Cohesion, c = 20 kPa Dry unit weight, γd=16 kNm3 The angle of inclination, β=40° Critical…

Q: lake has an inflow and outflow of 20x10^6 m^3/yr, a mean depth of 10 m and a surface area of 10x10^6…

Q: Determine the pressure at point D, in psi.

Q: 8. Find the resultant of the moment by the forces and coupe acting as shown. 500 Nm 50N 30% C 150N…

Q: You have been treating a wastewater with bacteria that have the following kinetic coefficients: k=…

Q: 7. 1 A = 51°23' B = 105°39' The four-sided, closed traverse has the following angles and distances:…

Question

A 2.2-lb steel tape is 99.98 ft long at 68° F while supported for its full length with a 10-lb pull. It has
a cross-sectional area of 0.005 sq in. and E= 29 x 106 psi. The tape held horizontally, supported at its
ends only, and pulled with a force of 25-lb. The distance measured is 3500.50 ft under the
temperature of 83° F. Determine the correct distance (Consider Temperature, Tension and Sag
Correction ONLY). You must provide solutions to support your answer.
Formula
Ctemp = 0.00000645 x (T-68°F) x L, Ctension = (P-Ps)L/AE, Csag = - W² x L / (24 x P²)
(Cslope = -(S)² / (2 x L), )
where, T = temperature, L = Tape length, S = slope, W = weight of tape, P = applied tension, P, =
standard tension, A = cross-section area

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve chapter Truss Frame Structure max 30-45 minutes, solve subparts a,b thank u Given that the truss structure with placement A (roll) and placement D (joints). A vertical force of 300 KN acts on the downward direction and a horizontal force of 150 KN acts on the Barah point to the left. a. Calculate the magnitude of the bearing reaction at A (rolls) and D (joints) by analytical means b. Calculate the magnitude of the entire force in the rod (Stems 1. 2, 3, 4, and 5) with the analytical point equilibrium method! Write the properties of each bar (stab or tank) in a table c. Calculate the amount of internal force and its properties for rods 2. 3 and 4 using the cut method (Riner) Note: you can use a combination of ritter and point balance if needed. d. Use Cremona's graphical method to calculate the magnitude of all forces in bars (Bars 1, 2, 3, 4, and 5) Use : Force scale: 1 cm represents 25 kN, Distance scale: 1 cm represents 1 meter.
STRUCTURAL THEORY Show complete solution for better understanding Situation 1: From the truss shown, each member has a cross-sectional area of A = 400 mm 2, E = 200 GPa. Use the method of Virtual Work F b.-37.5 C.-30 d. 30 -2m- 1. Determine the stress on member AE a. 37.5 E c. 2 d.3 n B 45 KN 2 m 2. How many zero-force member are there? a. 0 b. 1 3. Determine the vertical deflection of joint E a. 1.42 b. 3.38 c. 2.95 d. 1.24 1.5 m
A beam cast monolithically with the slab thickness of 110 has a span of 4 m spaced at 6 m center to center. The width of the web is 300 mm and effective depth of 500 mm. It is reinforced on the tension side with 8-20 mm Φ rebars. Fc’ = 30 MPa fy = 310 MPa 1. Which gives the effective width of flange? a. 2000 mm b. 1500 mm c. 2500 mm d. 1000 mm 2. Which gives the depth of the compression stress block? a. 30.55 mm b. 32.56 mm c. 12.45 mm d. 42.14 mm
Find the Maximum Shear andMoment.? can you solve in 20 mins?
1. Assume length of the m-tape steel weighs 12.5g/m and has a cross section of 0.022 cm². It measures correctly when supported throughout under a tension of 8.0 kg and at a temperature of 20°C. When used in the field, the tape is only supported at its end, under a pull of 9.0 kg, and at only supported at an average temperature of 28°C. Determine the distance.
2. Gate AB is a quarter circle 10 ft wide into the paper and hinged at point B. Find the force F that is enough to keep the gate from opening. The gate is uniform and weighs 3000 Ibf. |F A Water r= 8 ft %3D В
A rectangular concrete beam has a width of 400mm and an effective depth of 700mm. It is reinforced with 5-28mm diameter bars for tension only. Concrete Strength is f'c = 21 MPa and steel yield strength fy = 275 MPa. Which of the following most nearly gives the ultimate moment capacity of the beam? O 488.22 kN-m O 468.51 kN-m O 542.46 kN-m O 520.57 kN-m
Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 75 mm 75 mm Empedopre|72 -75 mm 150 mm 50 mm EN SAMA 00 kN B 1.0 m 60 kN -1.5 m-> rode D 1.0 m
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. 2.0 m | P₁ = 45 KN W₁ = 44.24 kN/m 3.0 m a. b. 3-200 6-200 350mm by 400mm f'c-35 MPa fy=415 MP.. Ps= 10 mm conc. cover= 40mm 250mm by 400mm f'c-21 MPa fy=415 MPa Ps= 10 mm conc. cover= 40mm
The boom AB lies in the vertical y-z plane and is supported by a ball-and-socket joint at B and by the two cables at A. A 20-kN force acting in the horizontal plane and applied at the midpoint M of the boom. Neglect the weight of the boom. 70. Calculate the tension T1. Calculate the tension T2.
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
NEED IN 1 HOUR PLSSS!! A hollow steel shaft 10 ft long must transmit a torque of 250,000 lb-in. The total angle of twist in this length is not to exceed 3.5°and the allowable shearing stress is 12,000 lb/in². Determine the inside and outside diameters of the shaft if G = 12 x 10⁶ lb/in². The action is elastic.