2. Two cylindrical rods, AC (made of steel, Es = 200 GPa), and CE (made of brass, E, = 105 GPa) are joined at C and restrained by rigid supports at A and E. The diameter of the steel rod is 40 mm. The diameter of the brass rod is 30mm. The applied forces are PB = 60 kN and Pp = 40 kN. Determine: (a) the reactions at A and E, (b) the deflection of point C relative to point A. Ans: RA = 62.8 kN +, Re = 37.2 kN +, &c= 0.0463 mm →)

2. Two cylindrical rods, AC (made of steel, Es = 200 GPa), and CE (made of brass, E, = 105 GPa) are joined at C and restrained by rigid supports at A and E. The diameter of the steel rod is 40 mm. The diameter of the brass rod is 30mm. The applied forces are PB = 60 kN and Pp = 40 kN. Determine: (a) the reactions at A and E, (b) the deflection of point C relative to point A. Ans: RA = 62.8 kN +, Re = 37.2 kN +, &c= 0.0463 mm →)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6) Determine the reactions at A and B for the steel bar and loading shown in Fig. I, assuming a close fit at both supports before the loads are applied. A = 250 mm? 150 mm 30X0 KN 150 mm A = 400 mm2 150 mm K 600 kN 150 mm B 7) A steel bar 20 mm square in section is subjected to an axial compressive load of 60 kN. Find the percentage change in volume if the bar is 500 mm long. What are the equal stresses that must be applied to the sides of the bar if the volumetric change is to be zero? E = 200GPA and v=0.3.
Q1: For the Structure shown in FiG.(1) Determine Reactions at points A,B 30 deg. 10 kN| -2 m 4m 2 m 5 kN 4 m
Q2: Bar of cross section 8 mm x 8 mm & 800 mm long is fixed at both ends. Determine the end reactions when temperature raised 45 c°. E= 2 x 10 MPa & x 10 /c. (
Determine the reactions in C on member ACD as shown in figure? 800 KN 5 m + 4m 6 m A D ш 8 m E 600 KN 3 m
Question #5 In figure below, determine the reactions at the supports. 900 N/m -3 m- 600 N/m 3 m B
I have already found the answer to first question: 1. The maximum load, F, that can be applied such that the reaction at C does not exceed 150kN, was calculated to be 323kN. Can you please solve the second part of the question: 2. What is the reaction force at A?
Q1. Determine the reactions at point O, in the below figure. 210 N F = 500 N 0.125 m -0.3m- 0.25 m F= 600 N
Problem 4: Given: P=10kN, Q=10KN. 0.8 m B Determine: Reactions at B, C, and D. Show all work C 4.0 m 2.1 m 2.1 m X
Determine the reactions in C on member ACD as shown in figure? B 800 KN III C 4 m 6 m mg E 600 KN
2. A bar ABC fixed at both ends A and C is loaded by an axial load (P) at C. If the distances AB and BC are equal to a and b respectively then find the reactions at the ends A and C. 3. An axial force of 20 kN is applied to a steel bar ABC which is fixed at both ends A and C as shown in Fig. 4.8. 2 A = 200 mm 2 A = 100 mm 20 kN+ A В C 2 m 1m - Fig. 4.8 Determine the reactions at both the supports and stresses developed in two parts of the bar. Take E = 200 GPa. [Ans. R = R = 10 kN ; 0AB = 50 MPa (C); 0BC = 100 MPa (T)] %3D %3D
Solve for the reactions at support A and B of the structure shown below. 600N 240N 16m CA2m A 12m 12m F 400N
3.5 m A C 5.5 m 0.2 m B D G In the figure above, the jib crane is supported by a pin at C and rod AB. Knowing that x = 6.2 m, and the load D has a mass of 3050 kg, with its center of mass located at G, you are required to explain your answers by your own words and A) Draw the free body diagram (FBD) B) Determine the reactions at the pin C C) Determine the force developed in rod AB D) Check the equilibrium of the system by determining the sum of the moments of all forces about point B