2. The cart shown below has a total mass of 134 kg. Its center of gravity is located at Point G. There is a force applied to the cart where P = 632 N. Assume the wheels are free to roll and have negligible mass. Answer the following questions. a. Draw and label a free-body diagram using S.P.R.E.A.D and a kinetic diagram. Do not label the figure provided. b. What is the acceleration of the cart? Show your work. Magnitude rounded to 3 sig. fig. Units Direction 1.25 m 0.25 m B 0.75 m 0.25 m -1.25m 0.5 m c. Use EMA = (EMK) A (Sum of Moments about Point A = Sum of Kinetic Moments about Point A) to determine the normal force at Point B. Show your work.

2. The cart shown below has a total mass of 134 kg. Its center of gravity is located at Point G. There is a force applied to the cart where P = 632 N. Assume the wheels are free to roll and have negligible mass. Answer the following questions. a. Draw and label a free-body diagram using S.P.R.E.A.D and a kinetic diagram. Do not label the figure provided. b. What is the acceleration of the cart? Show your work. Magnitude rounded to 3 sig. fig. Units Direction 1.25 m 0.25 m B 0.75 m 0.25 m -1.25m 0.5 m c. Use EMA = (EMK) A (Sum of Moments about Point A = Sum of Kinetic Moments about Point A) to determine the normal force at Point B. Show your work.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.41P: The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking...

See similar textbooks

Similar questions

The center of gravity of the 3000-lb car is at G. The car is parked on an incline with the parking brake engaged, which locks the rear wheels. Find (a) the normal forces (perpendicular to the incline) acting under the front and rear pairs of wheels; and (b) the friction force (parallel to the incline) under the rear pair of wheels.
Problem #3 Find the center of gravity of the fork truck, operator, and cargo with respect to the front wheels. Each bag on the forks is 25.0 kg. -0.37m 800 N +105N -0.58 m 140 m 0.85 -0.48 m-
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
4. An aeroplane with a two wheel nose gear and four main wheels rests on the ground with a single nose wheel load of 500 kg and a single main wheel load of 6000 kg. The distance between the nose wheels and the main wheels is 10 meter. How far is the centre of gravity in front of the main wheels ?
1. What's the difference between the center of gravity and the center of mass? 2. How is the specific weight of a body defined? 3. What does it mean when we say a body is homogeneous? 4. What are the theorems of Papus and Guldinus used for?
Figure(a) depicts a head-on view of a 1000 kg mass private airplane flying in a state of equilibrium. The force labeled P represents the lift force acting on each wing, and W represents the gravitational weight of the craft. Fig. (b) depicts a more detailed view of the wing ABCD showing its physical dimensions and the assumed location of the lift force P. The wing has a mass of 200 kg and a center of gravity at point B. The wing is attached to the fuselage at point A, which can be modeled as a pin connection. The wing is supported by a pin-connected strut BE whose mass may be neglected. (a) Sketch a free-body diagram of the forces acting on the wing depicted in Fig (b). Compute the vertical lift force P. (c) Compute the forces supported by the strut BE and the pin at A. Hint: You may model the wing as a two-dimensional structure where all forces lie in the same plane. (a) P XERO y W (b) 1.4 m + 2 m B с 0.6m 2.4m D
A rock is attached to the left end of a uniform meter stick that has the same mass as the rock. In order for the combination of rock and meter stick to balance atop the triangular object in Fig., how far from the left end of the stick should the triangular object be placed? (i) Less than 0.25 m; (ii) 0.25 m; (iii) between 0.25 m and 0.50 m; (iv) 0.50 m; (v) more than 0.50 m.
Plunger (weightless) Area is 0.003 m² piston mass 1000 kg , area of piston is 0.3 m² density of oil is 750 kg/m³ determine force on Plunger required for equilibrium
The figure at right shows a child’s toy. This toy takes the form of a cylinder mounted on top of a hemisphere, of total mass M. The radius of the hemisphere is R, and the CM of the toy is a height h above the floor when the toy is vertical. Assume that the cylinder and the hemisphere have the same density. In terms of R, what is the maximumthickness d of the cylinder for which the toy will remain stable?
RECTILINEAR MOTION. Indicate free body diagram and complete solution.
%E1.₁. Q a F3-5. If the mass of cylinder C is 40 kg, determine the mass of cylinder A in order to hold the assembly in the position shown. ||| (واجب بیتی) .H.W الواجب 3.pdf الواجب 3 اذا كانت كتلة الاسطوانة C هي Kg 40 ، احسب كتلة الاسطوانة A التي تجعل الترتيبة المبينة بالشكل في حالة اتزان وفي المواقع الموضحة. بقت هي 0 O 0 30° B | 40 kg 10:50
Question 2 The wheel A and a block B are connected by a cable. The coefficient of friction of the wheel and the ground is HA = 0.4. The coefficient of friction of the block and the ground is HB = 0.3. The wheel A has mass 40 kg, and the block B has mass 30 kg, with a %3D center of gravity shown. The radius r, = 0.5m. The outer radius is 1 m. a) Determine the smallest force P (applied vertically) that will cause motion to impend. b) What type of motion is impending? (i.e. slipping/tipping at A/B)