2. Set the frequency at 10kHz. 3. Connect channel 1 input of the oscilloscope in points (ab). Set the output of the signal generator to have Vs= 10 Vp-p. 4. Connect Channel 2 of the oscilloscope in points (c.b) and measure the voltage across the resistor VR(P-p)= volts 5. Change the position of the resistor and capacitor, then measure the voltage across the capacitor. Vclp-p)= volts 6. Change the position of the capacitor. and inductor, then measure the voltage across the inductor. VL(p-p)=. volts

2. Set the frequency at 10kHz. 3. Connect channel 1 input of the oscilloscope in points (ab). Set the output of the signal generator to have Vs= 10 Vp-p. 4. Connect Channel 2 of the oscilloscope in points (c.b) and measure the voltage across the resistor VR(P-p)= volts 5. Change the position of the resistor and capacitor, then measure the voltage across the capacitor. Vclp-p)= volts 6. Change the position of the capacitor. and inductor, then measure the voltage across the inductor. VL(p-p)=. volts

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

-) Below are two voltage patterns measured from an oscilloscope. The voltage stage of the CHI probe is 5 V / div, the CH2 probe voltage stage is 10 V / div and the time axis is 2ms / div. According to this information, a) What are the peak to peak and rms voltage values of the voltages in CHI and CH2? b) What is the frequency of the voltages in Hz? c) How many degrees is the phase difference between the two voltages, which voltage is leading?
C2 (i). Draw the Schematic diagram and explain the working of LVDT and write any two applications of it. C2 (ii). A sinusoidal waveform is displayed on a C.R.O. screen, the time/cm switch is on 40 µs/cm and the volt/cm switch is on 20 V/cm. The width of one complete cycle is 3 cm and the peak to peak distance is 5.6 cm. Determine the following: The frequency is The magnitude of the sine voltage is The amplitude is The R.M.S voltage is
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 50 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees.
The signal measured with the oscilloscope in the Multisim program is shown in the figure below. For the signal measured according to this figure, write the following measurement values.T (period) = …………………… .. usf (frequency) = …………………… .. kHzVpk (Peak voltage) = ……………………. mVVpk-pk (Peak to peak voltage) = ………………. VVrms (Effective value) = ………………… V
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 20 ms/cm, and the 'volts/cm' switch is set to 30 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees and (v) R.m.s value of waveform Q.
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 20 ms/cm, and the 'volts/cm' switch is set to 30 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P and (iv) phase angle difference between P and Q in Degrees and (v) R.m.s value of waveform Q. Note: Please do not handwriting
LVDT produces an rms output voltage of 5.0 V for displacement of 3.5 mm. Calculate the sensitivity of LVDT please explain me
is the simplest way of producing a source of lower EME from a source of higher EMF.
What is the action of a capacitor in a Power Supply Circuit?* a. To de-couple DC component of the rectified AC input b. To increase the DC component of the output wave. c. To remove DC component of the AC wave. d. None of the above.
A 3V sinusoidal signal with frequency 100 Hz amplitude is applied to channel A of an oscilloscope. A sinusoidal signal with the same frequency but opposite phase and amplitude of 1.5V is applied to channel B. What will be the equation of the Lissajous curve when the oscilloscope is switched to XY mode while the channels are at the same Volt/div setting?
A schematic design of a full-wave bridge type power supply is given below. Provide the appropriate values for the inductors, diodes, capacitor and resistors, such that the output DC voltage is 7.5 V and the max. output power for the load resistance is 20 mW (percentage error for output voltage and output power is 2%). AC voltage source: Amplitude=311.13, Freq=60, DC offset= 0. For the rectifier part, choose diodes with an appropriate PIV rating. Show all the formulas and computations involved in acquiring the values for the inductors, diodes, capacitor and resistors. • In choosing your Zener diode, consider the output voltage and the output current. Note that the output current should be the minimum Zener current. • For the value of the series resistor RS, choose a lower value for less ripple but always consider the required output voltage. •The ripple voltage peak-to-peak value should be less than or equal to 1% of the required output voltage. Use the formula below for choosing the…
The waveform displayed on an oscilloscope is as shown in Figure The 'time/cm' switch is set to 0.2 ms/cm, and the 'volts/cm' switch is set to 40 V/cm. Determine the (i) amplitude of waveform Q, (ii) peak to peak value of waveform P, (iii) frequency of waveform P