2. In the test of a centrifugal pump with water, the rate of discharge was found to be 260 li/s, the pressure gage read 13 kg/cm² and the suction gage read 15 cm of mercury. The difference in elevation between the two gages was 0.8 m. The diameters of suction and discharge pipes are the same. Find the overall efficiency of the pump if the input horsepower is 600.

2. In the test of a centrifugal pump with water, the rate of discharge was found to be 260 li/s, the pressure gage read 13 kg/cm² and the suction gage read 15 cm of mercury. The difference in elevation between the two gages was 0.8 m. The diameters of suction and discharge pipes are the same. Find the overall efficiency of the pump if the input horsepower is 600.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Explain the variables involved for the design of dryers. Just type here your explaination, Thanks!
The product shown in Figure 5 is to be machined using a non-conventional machining process. The material of this product is Silicon Nitride that can withstand a temperature up to 450 °C. i. Propose the appropriate process to produce the part. ii. Justify the mechanism of the process in (i). Figure 5: Pump impeller
Sub: Advanced Manufacturing Process
1. Define manufacturing processes, design engineer, industrial engineer and materials engineer? 2. Name and explain a protess to make cylinder shaft? 3. Discus at least three factors which will effect tool life? 4. Define finishing and roughing process? 5. Explain the negative effect of heat generated from machining process? 6. One limitation of sand casting is bad surface finish. Yes or No? Why? 7. What is permeability in casting process? 8. What are the major defects in casting process? 9. Which type of casting process should be use for high melting point casting, such as cast iron and why? 10. Casting problem A certain mold has a sprue whose length is 20 cm and the cross-sectional area at the base of the sprue is 2.5 cm?. The sprue feeds a horizontal runner leading into a mold cavity whose volume is 1560 cm³. Determine: (a) velocity of the molten metal at the base of the sprue, (b) volume rate of flow, and (c) time to fill the mold (in second). mfg m1 Spring 2020 999.pptx
I need the answer as soon as possible
-Illustrate the process of the Water Jet Machining (WJM) system compare to EDM (Electrical Discharge Machine) wire cutting in term of cutting operation.
Can you please explain how to find the velocity using the methods described? And also why it's done that way? This is from Introduction to robotics mecahnics and controls. Please help ;( !
2. Assignment You are tasked to investigate the following and to compile your findings in a technical report: 2.1 What is the benefit of using investment casting for the production of a turbine rotor compared to other casting processes? 2.2 Which AM materials and processes (according to the ISO/ASTM 52900 standard) is mostly used during the manufacturing of patterns for the investment casting process? List the advantages and disadvantages of each of the AM processes. 2.3 What are the advantages and disadvantages of using AM techniques to produce patterns for the investment casting process, compared to conventional methods? 2.4 Show with a sketch, how the build orientation of the processes listed in Question 2.2 can have an influence on the accuracy and surface quality of a pattern. 2.5 Which manufacturing process (listed in Question 2.2) will be most suitable to produce a pattern for the turbine rotor? Provide reasons for your selection. 2.6 The use of additive manufactured patterns…
I need answer within 20 minutes please please with my best wishes
22.12 What is a cermet? What are its advantages?