2. If the cons mponent of

Q: A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position…

A:

Q: 4X-Y -2x+6y+Z =9 - X tY t7z =-6 17: 11

A: Solution: We have to solve the given system of equation using Jacobi iteration.

Q: a) Determine thę centroid location (measured upward from the bottom), in mm rounded to the nearest…

A:

Q: This type of utilized analysis when involves an analysis must be performed materials go displacement…

A:

Q: 3. Which one of the following equations is dimensionally homogenous? Show your proof. a. F(x, – x) =…

A: a. It is given that  Fx2-x1=12mV22-12mV12   where, F is force (N )             x is distnance m…

Q: Only answer A. Explain why the obtained answer makes sense.

A: This question is related to the Strength of the material from Civil Engineering. As per question…

Q: The torque (N-m), T, delivered by a water turbine depends upon the discharge (m³/s), Q, head (m), H,…

A: The number of terms is 6.

Q: A-Solve the following 2nd ODE by Laplace transformation k 12 +40 y" + 4y = 0. y(0) = 2. y'(0) = 2

A:

Q: A h Ph³ 351 PROVE THAT A = Ph 361 BY: CONJUGATE BEAM METHOD →THREE-MOMEN EQUATION SLOPE DEFLECTION…

A:

Q: Q.9 If n is the ratio of internal and external diameter of a hollow shaft, the ratio of the weight…

A:

Q: A negative internal bending moment M causes a beam element to O rotate counterclockwise bend concave…

A: Bending moment at a given section can cause Sagging (concave upward) or hogging (concave downward)…

Q: The state of state is given by the following tensor 1 1] [T] 1 1 1 1 11 a- Determine the principal…

A: a) Tensor :               T=111111111 Principal…

Q: A negative internal shear force V causes a beam element to

A: This question is related to the Strength of material from civil engineering. In this question ,…

Q: Problem 1 The horizontal rigid beam holds the distributed load indicated in the picture. Determine…

A: Area of each bar, Modulus of elasticity,

Q: Solve

A:

Q: The degree of homogeneity of the function f(x, y) = (x² - 4y²)-¹/2 O A. 1 OB.-1 O C. -1/2 O D. None…

A:

Q: es the following "quation sutisfied 4

A:

Q: F1, F2, and F3 are given as concentrated loads. R is a distributed load equal to 300N/m applied from…

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: For the state of stres shown on the elenent below, Apply the cocept of stress to determine Imethod…

A:

Q: Letting Le= Ib and Ic = Ib= I, dekening the critical load of the frame in down Figure for the…

A: Sidesway buckling:

Q: Show that the vectors ( A=3i+ 6j) and ( B=-i-2j) have opposite direction

A:

Q: 9 m 1300 lb 400 lb 600 lb -b- A a 400 - Ib

A: A beam having simple support or fixed support, due to loading on the beam this support goes under…

Q: 1-z? 1. f(z) = (by Definition) 22 %3D Find the derivation

A: using u/v rule of derivatives we can get answer

Q: The system shown is in static equilibrium and motionless. All joints are ideal. • The origin of the…

A:

Q: Compute the moment about x-axis of thin plate with constant density 8(x, y) = 5, bounded below by…

A: mx = 3.93

Q: Q.9 If n is the ratio of internal and external diameter of a hollow shaft, the ratio of the weight…

A:

Q: Any shear load can be represented by the combination of the shear load applied through the and a

A:

Q: 3. Using conjugate beam method determine the value of Elō under each concentrated load of the beam…

A:

Q: Show that A=n(1-Sr)

A: Given :- a soil is in three phase consists of solid, water and air.   To show :- A = n( 1- Sr)

Q: 3 State whether each of the following products is odd, even, or neither. (a) x³ cos2x (d) x²e²x (b)…

A:

Q: Determine so that = 5. a I, a y a IN

A: Moment of Inertias of the area about the z and y-axis is calculated to find the final answer.

Q: For the beam with coordinate shown in figure. Develop the flexibility matrix. 2 B

A:

Q: Hiwe A bar with constant ss-section area(Aland unit weight () is subjected to axial force ce) in…

A:

Q: The beam below supports 3-point loads. The beam is supported by a pin at A and a roller at D. a)…

A:

Q: Force Method is also know as Method of Answer Displacement

A: methods of analysis of indeterminate structure is  done by following methods - 1) Force method /…

Q: Verify whether the following are valid potential functions: (i) ¢ = 4r²– 5y² (1) 0 = 2r + 5y

A:

Q: A = 900 lbs 25° 75⁰ B = 600 lbs

A:

Q: Given the following technical description, determine if the traverse is closed. If not, balance the…

A:

Q: D m PROVE THAT A= Ph³ A: 12E1 SLOPE DEFLECTION METHOD

A: given beam is fixed support beam . in fixed support beam there are no rotation or deflection at…

Q: Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid…

A:

Q: 2 3 1 If A = -1 2 4 057 What is the cofactor of the second row, third column element? A. B. C. 3 1 5…

A: In this question a matrix is given and we are asked to find out cofactor of second row and third…

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).