2. From the given figure and data below. Determine the: a. P so that the structure is stable (in equilibrium) b. Draw the FBD of the member BC c. Reaction at A Weight of the member AB and BC = 50kg µ at C= 0.5 1.5 m 3m 1.5 m 30 30 4,=0,5

2. From the given figure and data below. Determine the: a. P so that the structure is stable (in equilibrium) b. Draw the FBD of the member BC c. Reaction at A Weight of the member AB and BC = 50kg µ at C= 0.5 1.5 m 3m 1.5 m 30 30 4,=0,5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The suspended load weighs 607 lb Figure 3 ft- 45° B 4.5 ft 30° < 1 of 1 C Part A Use the fact that ABC is a three-force member to determine the magnitude of the reactions at A (Figure 1) Express your answer with the appropriate units. FA= Submit Part B FB = μA Submit Value Request Answer Use the fact that ABC is a three-force member to determine the magnitude of the reactions at B. Express your answer with the appropriate units. μA Value 1 Request Answer Units → PANC Units ? ?
Two wires are welded together end to end. The wires are made of the same material, but the diameter of one is twice that of the other, di = 2 d2. They are subjected to a tension of T= 4.60 N. The thin wire has a length of L2 = 40.0 cm and a linear mass density of 2 = 2.00 g/m. The combination is fixed at both ends and vibrated in such a way that two antinodes are present, with the node between them being right at the weld. (a) What is the frequency of vibration? (b) What is the length of the thick wire, L1 =? N A N A N o d2 L,, µi L2, H2
hydrostatic state of stress as shown in the figure. For no change in the volume to occur, what should be its Poisson's ratio? Oy Ox
THE CIRCULAR TROUGH AS SHOWN IN THE FIGURE IS FILLED WITH WATER UP TO THE BRIM. USING THE THEOREM OF PAPPUS-GULDINUS, COMPUTE THE MASS (IN KG) OF THE WATER WITH UNIT WEIGHT Y = 9.81 KN/M IF R=375 MM.
Which of the following is false regarding factor of safety in the design of structures? a. It considers uncertainties in the material properties. b. A higher factor of safety is preferable in designing safe structures c. It should not be less than 1 to ensure the structure’s safety. d. It considers changes in the loading pattern on the structure. Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If the system is initially stress-free, calculate the temperature change that will cause a tensile stress of 90 MPa in the brass rod. Assume that both rods are subjected to the same change in temperature.
21 The volume coefficient of thermal expans ion is equal to two times the value of area coefficient of expansion.( O True 22 False The deformation aLAT, is the deformation when material is exposed to temperature increase or decrease. ( True O False
What is the change in dia.
Classify the structures for Stability and determinacy , if unstable state why, if indeterminate state the degree of indeterminacy
The rods of different materials are connected and placed between rigid supports at A and D, as shown in the figure. Properties for each of the three rods are given below. The bars are initially unstressed when the structure is assembled at 25°C. After the temperature has been increased to 90°C, determine:
Classify struc. if stable/unstable, state reason why pls
There is no force on a beam, but the beam is subjected to a very large temperature difference above and below. As shown in the figure below, try to calculate the vertical displacement of the midpoint of the beam, assuming that the temperature coefficient of the entire beam is a = 11.7×10^-6 °F. Tip: See Mechanics of Materials for Beam Deformation Geometry