2. Determine IB,Ic, Vc and Vce +16 V 12 k2 Vc VCE B = 80 %3D 9.1 k2 15 k2 6-12 V

Q: a. Describe the action of the circuit shown in the figure-1 below SPEAKER Vin RE

A: According to the question, we need to describe the working of the circuit shown below

Q: Calculate the power saving in percent for the H3E system of an AM signal modulated to 57%. Your…

A: Given: Modulation percent of the H3E system of an AM signal = 57 %. To find: Power saving in %.

Q: Q# 02: i- What is difference between a Thyrister & Triac device? ii- Draw symbols of each device.…

A: Thyristor and Triac: Thyristor and Triac are the semiconductor device. They both are used to control…

Q: What is the advantage and disadvantages Static and Dynamic characteristic of measuring instruments.…

A: Step-1->Static and dynamic characteristics are two important aspects of measuring instruments.…

Q: Q1 (a) With an appropriate block diagram, briefly describe the function of the main system available…

A:

Q: How to use Ni Multisim?

A: The NI Multisim is an easy-to-follow and simulated place for engineers, students, and professors who…

Q: Q1/ Choose the correct answer 1.When the coil of Relay is supplied with 12 volts, the common will a)…

A: As per the honour code I will only attempt Q1. Kindly repost the other questions again. THANK YOU!!…

Q: iven the following scenario: 'hat can we conclude about its accuracy and precision? O Not accurate…

A: In this question we will write about accuracy and precision....

Q: Explain the given circuit diagram and also explain its functions with suitable examples. Ground 1…

A:

Q: Electrical furnaces are used in the production of steel that is consumedin the structural,…

A: Electrical furnaces:- Electricity is used as the heat source in an electric furnace, a heating…

Q: Which environmental impact is a result of fossil fuel use? O a. all of these O b. chemical pollution…

A:

Q: Which of the following statements is correct regarding the efficacy and use of incandescent lamps…

A: In the given question, we need to find out the correct statement from the given option.

Q: Explain with a neat block diagram the measurement of temperature using Thermistor (measuring…

A: Thermistor is a resistor, which is a special variant(type). When temperature changes, then the…

Q: With neat diagram explain the construction and working of CRO.

A:

Q: 3. The power consumed by an electric appliance is computed as the square of the voltage across the…

A: Given : The equation of power consumed by an appliance as the square of voltage V2 divided by…

Q: What is the percentage of carbon residue? What is the importance of carbon residue?

A: 1) The carbon Residue value of fuel depends on the refinery processes employed in its manufacture.…

Q: ANSWER IT IN CORRECT & Explain THANKS

A: Make a (2) titles about this project: [About 10-Watt Audio Amplifier Circuit LM1875] A. B. 2.…

Q: please answer fast need

A: In this we will write maximum and minimum acceptable value..

Q: Basic Elements of Electric Circuits

A: we need to explain the basic elements of electric circuit.

Q: Fifty years into the future, the way we will probably make base load energy include(s) Select one:…

A: Energy:- Energy is present in different forms, it is capable to move an object or doing work. Solar…

Q: Question 6 Vin R1 Vb n D1 Given a diode circuit with Vin= 1.5 V, R1 = 1.8 kOhms, Vb = 5.9 V.…

A:

Q: (a) With an appropriate block diagram, briefly describe the function of the main system available in…

A: The figure below shows the basic block diagram of electrical power system.    The typical…

Q: Answer the following questions. 1. What is ceramics? 2. Give some examples of Ceramics products. 3.…

A:

Q: a) Explain FOUR (4) measurement standards available.

A:

Q: avantajlarındandır) I – Is a solid element (Katı elemanlardır) II– Concumes less energy (Nisbeten…

A: We need to tell about the advantage of LED .

Q: How do you prove the correct operation of a digital multimeter? Present your answers in tabulated…

A:

Q: Explain the elements of measurement system in detail

A: Measurement system : measurement system is combination of various component which measures the…

Q: S We measured the current that appeared on the plotted screen as shown in the figure by means of…

A: The most popular form is the D'Arsonval galvanometer, which uses a light coil of wire strung from a…

Q: Identify the settling time of a meter. a. Time taken by output to reach final constant value from…

A: Settling time:

Q: Sketch a diagram showing the ohmmeter face for a reading of 1.2k ohms. Indicate the setting of the…

A: Ohmmeter:- An ohmmeter is a piece of electrical equipment used to measure electrical resistance.…

Q: The op amp in the circuit Figure 8 ΚΩ (Figure 1) is ideal. Suppose R = 15 kn 240 mV 60 ΚΩ 30 ΚΩ +…

A: We need to calculate the node voltage and branch current.

Q: 3. The power consumed by an electric appliance is computed as the square of the voltage across the…

A: Given: Power consumed is given by square of voltage across the appliance divided by resistance=V2 /R…

Q: Rewrite five (5) proper steps in determining the sizing of battery that to be used  either in…

A: We need to write steps in determining the sizing of battery that to be used either in…

Q: Globe 1:56 PM 65% Ailley Nhi... A. Show your complete solution. a. If you are going to use manual…

A:

Q: A. Condition 1 You have 2 push buttons and 1 lamp. The lamp will turn "ON" if either of the 2 push…

A: We need to create a PLC program for the following conditions  The lamp will be turn ON if either of…

Q: The scale of moving iron instrument is linear. True False

A:

Q: QUESTIONS: 1. A transformer is rated at 120V primary/23V secondary. What peak to peak secondary…

A: As per the honor code I will do only first question. Kindly repost the other questions again. THANK…

Q: Please answer in typing format

A: Fundamental Concepts  Voltage (V): Voltage is the potential difference between two points in a…

Q: In the nuclear fusion reaction, addition of mass of reactants is the combined mass of the products O…

A:

Q: What will be the maximum and the minimum value of VSWR? Please calculate thoroughly.

A:

Q: An electrical component has a reliability of 0.95 over 1,500 hours of normal use (note normal use…

A: Given  Reliability = 0.95  Usage in hours = 1500 Here the electrical component usage indicates it…

Methods of Wiring

Electrical wiring is the way of integrating cables and wires to interconnected equipment such as fuses, switches, sockets, lights, fans, and so on to the main distribution board, which is a specific structure attached to the utility pole that ensures a constant power supply.