Answered: 2. Determine drag on the sphere for…

2. Determine drag on the sphere for flow past a sphere (see the figure below) using these parameters D (diameter of sphere), p (density), u (viscosity), u (velocity), Fo (Drag on the sphere).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. Consider a two-dimensional flow which varies in time and is defined by the velocity field, u = 1…

A: Velocity field, U =1 , V= 2yt

Q: Discuss the effect of Reynolds number on the thickness of boundary layer flows and the wall shear…

Q: The Power (P) required to drive the pump depends upon the diameter (D), the angular velocity (@),…

A: Total variable =P,D,ω,Q,ρ P= f(D,ω,Q,ρ) where P is a dependent variable

Q: A jet engine on a test stand directs a stream of hot exhaust gasses against a vemcal wall. All of…

Q: How many Potechially defferent mixed tensors forder two can be defined Ex:0 by faking the ouler…

Q: In a fluid flow, the density of the fluid is constant for incompressible flow Select one: True False

Q: Question 3 Water flows in the vicinity of a 90° corner as shown in Figure 2. The flow could be…

Q: In chapter 12, we found the velocity profile for flow around a sphere using the creeping flow…

A: To Find:The velocity profiles for the and The pressure distribution.The drag force acting on the…

Q: Question (1): The ship in Figure (1) is subjected to a drag Fp on its hull, created by water passing…

Q: The two components of the velocity vector are given as Vx = –ay/(x2+ y2)1/2 and Vy = ax/(x2+ y2)1/2…

Q: The Reynolds transport theorem (RTT) is discussed in Chap. 4 of your textbook. For the general case…

A: Step 1: Step 2: Step 3: Step 4:

Q: Aeronautical engineers measure the pitching moment M0of a wing and then write it in the following…

A: Given data: *The pitching moment of a wing is M0=βV2AC ρ. * V is the wing velocity. *A is the wing…

Q: The thrust P of a propeller depends upon diameter (D); speed (u) through a fluid density (p);…

A: Given data: P = f (D,u,N,ρ,μ) To determine: The above mentioned non-dimensional correlation

Q: Engineers are worried about the wind forces on a sculpture in Queen Mary campus. The sculpture has a…

A: Given data:Height of full-scale sculpture (Ha) = 5 mDiameter of full-scale sculpture (Da,) = 5…

Q: Ming Yang Smart Energy, a Chinese wind turbine manufacturer, currently holds the record for the…

Q: At t = 0 the tank shown in fig. is full up to top level, write the differential equation for the…

A: Given Datar=0.05mt=0Conical and cylindrical

Q: Let us model a certain cargo ship as a rectangular prism with length (100 m) and width (20 m). Also,…

A: We have to find 1.boat weight 2.how far below the waterline will the bottom of the boat be?

Q: quation and show how units are equivalent: v = _/ N / (kg/m)

A: the solution of above problem is below

Q: A cricket ball travels at 130 km/h through air at 20 degrees Celsius. The cricket ball has a…

Q: Q3\ A. What are things that can be done to reduce your vehicles drag ( air resistance) B) 1. Viscous…

A: solution (A):- To reduce vehicle drag

Q: A fighter aircraft is to operate at 200 m/s in air at standard conditions ( = 1.2 kg/m3 ). A model…

A: GIVEN:- velocity of aircraft : V=200m/sdensity of air : ρair=1.2kg/m3length ratio of model and…

Q: The flow rate in a rectangular open channel can be measured by placing a plate along the channel as…

A: Given Data: The width of the channel is b. The height of the water is H. According to the given…

Q: Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the…

A: Given: Fluttering frequency is a function of following variables: ω=fnV,ρ,g,L,ρA Length of the…

Q: 1. 3- 4- polymer fluid has the data in the table blow. Sketch the relationship between shear stress…

Q: The spherical particle of unit density falls freely in air with a constant velocity of 0.50 cm/sec.…

Q: The Reynolds number for a 1-ft-diameter sphere moving at2.3 mi/h through seawater (specifi c gravity…

Q: In an attempt to escape his island, Gilligan builds a raft and sets to sea. The wind shifts a great…

A: Let east is along the positive x-axis and north is along positive y-axis. The distance travelled…

Q: 5.7 The rectangular roof sheet of a kennel has a dimension of 6m x 2 m. Calculate the drag force on…

Q: Q3\ A. What are things that can be done to reduce your vehicles drag ( air resistance) B) 1. Viscous…

A: solution (A):-

Q: A 500 ft long ship is to operate at a speed of 20 mph in ocean water whose viscosity is 1.2 cP and…

Q: A velocity field V = (x - 2y)ỉ - (2x + y)¡ given in the form. a)specify how many directions is the…

Q: We want to predict the drag force on a remote-control airplane as it flies through air having a…

A: Solution: Given Data: ρa=1.21 kg/m3μa=1.76×10-5 Pa-sVp=32 m/sD=75 mmρw=3 kg/m3μw=1.82×10-5 Pa-s…

Q: Mott ." cometer, which we can analyze later in Chap. 7. A small ball of diameter D and density p,…

A: The data given is, The specific gravity of steel ball, SGb = 7.87 The diameter of the steel ball, D…

Q: (mey, Co = 7 HA where g is gravitational acceleration, T is a characteristic time, p is dynamic…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: If the laminar velocity profile is approximated by the cubic-order polynomial where, a = u/U, and y…

A: a) The given velocity profile is uUe =a1+a2yδ+a3yδ2+a4yδ3 (1) The boundary…

Q: Consider laminar flow through a long section of pipe, as in Fig. For laminar flow it turns out that…

A: Hence,

Q: Q2. In the design and development competition in a University, a team of students has planned to…

A: Given: The length of the prototype is, Lp=6.5 m. The speed of the prototype is, X=vp=1 ms. The…

Q: The work of adhesion (W) is the energy per unit area associated with bringing two immiscible liquids…

A: Given:The equation is .The is work of adhesion in .The is surface tension in .Concept used:The…

Q: Air 2 m Oil =0.80 4 m S = 5 m 3 m Water

Q: Q2: As shown in figure (2), If Q = 0.5 m/s, D, 0.3m, Z, = 2m, Z, = 0.75m and s-2.5, FindD2.

Q: Determine drag on the sphere for flow past a sphere (see the figure below) using these parameters D…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

2. Determine drag on the sphere for flow past a sphere (see the figure below) using these
parameters D (diameter of sphere), p (density), u (viscosity), u (velocity), Fo (Drag on
the sphere).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Stoke's law

VIEW

Step 2: Derivation can be calculated from

VIEW

Step 3: Result

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

fluid mechanics subject! please help me solve this thankyou very much!
follow the format to answer the question
Please solve in 30 minute
By dimensional analysis, obtain an expression for the drag force (F) on a partially submerged body moving with a relative velocity (u) in a fluid; the other variables being the linear dimension (L), surface roughness (e), fluid density (p), and gravitational acceleration (g).
Find the drag force of the flow over aplate with a.v.p. of Sinπy/2δ ? [ Take the length and width of the plate ar: L and b ] Ans: FD= 0.658 ρv² bL / ReL⁰٠⁵
Solve for the specific volume and specific weight in SI units and Dynamic Viscosity in Poise. The specific gravity of alcohol is 0.52 and its kinematics viscosity is equal to (your registration number/2 e.g., 4193/2) Centi Stokes.
I nee dhelp finding thrust drag and friction
Pravinbhai
The company has opted to purchase a new viscometer for you, as such, you are required by topropose two options for new viscometers. Select two viscometers and explain their operation andconstraints. (P3)b. (P4) Given that you achieved the following results with a U-Tube viscometer:Temperature/ C Time / s40 5760 4180 29100 16
If the model is 2 times larger and its velocity is 6.25 larger than the prototype, what will be the ratio between the model and prototype drag force? (Provide your answer using 3 decimal points) Answer: 0.495 Please show steps and formula used (Fluid mechanics)
Assume that the wall shear stress, Tw, created when a fluid flows through a pipe (see Figure a) depends on the pipe diameter, D, the flowrate, Q, the fluid density, p, and the kinematic viscosity, v. Some model tests run in a laboratory using water in a 0.2-ft-diameter pipe yield the Tw vs. Q data shown in Figure b. Perform a dimensional analysis and use model data to predict the wall shear stress in a 0.3-ft- diameter pipe through which water flows at the rate of 1.5 ft3/s. 0.7 Diameter = D 0.6 2 0.5 0.4 Model data (a) 0.3 0.2 0.1 0.5 1.5 Flowrate, Q, ft/s (b) Tw Ib/ft2 Wall shear stress, T,, Ib/ft? n * m N -
a) A successful Fluid Dynamics lecturer uses a board above their automobile to promote their course as shown in Figure Q1 below. They drive at a speed of 10 metres per second, and the board is 3 metres long and 1.5 metres high. Determine the boundary layer thickness on the surface of the board. b) In the given scenario, calculate the shear force on the board's laminar boundary layer section. c) Determine the shear force on the board's turbulent boundary layer section in the case above. Briefly explain the comparison of the result with Q1 b). Given: (p = 1.225kg/m³,μ = 1.5x10-5kgm-¹s-¹) Figure Q1