2. An isolated T-beam is composed of a flange 700 mm wide and 175 mm deep cast monolithically with a web 250 mm width that extends 600 mm below the bottom surface of the flange to produce a beam of 750 mm depth. Tensile reinforcement consists of 6-32 mm Ø bars placed in two horizontal rows. The centroid of the bar group is 650 mm from the top of the beam. It has been determined that the concrete has a strength of 21 MPa and that the yield stress of the steel is 415 MPa. Determine the following: a. Depth of compressive block b. Compression strength of the web Design moment capacity of the beam C.

2. An isolated T-beam is composed of a flange 700 mm wide and 175 mm deep cast monolithically with a web 250 mm width that extends 600 mm below the bottom surface of the flange to produce a beam of 750 mm depth. Tensile reinforcement consists of 6-32 mm Ø bars placed in two horizontal rows. The centroid of the bar group is 650 mm from the top of the beam. It has been determined that the concrete has a strength of 21 MPa and that the yield stress of the steel is 415 MPa. Determine the following: a. Depth of compressive block b. Compression strength of the web Design moment capacity of the beam C.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi. For the midspan section shown, check if steel yields and compute ØM, and compare it with M. WD = 1.2 kips/ft plus weight of beam WL = 1.5 kips/ft %3D 20.5 in 23 in 3 no. 9 bars 18 ft 11 in.
Q-A pre-tensioned concrete member of section 200 mm x 250 mm contains tendons of area 500 mm² at centre of gravity of the section. The prestress in the tendons is 1000 N/mm². Assuming modular ratio as 10, find the stress (N/mm2) in concrete.
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!
In post-tension, concrete should be hardened first before applying the tension in the tendons. True False
A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
A concrete floor slab 100mm thick is cast monolithic with concrete beams 2.0m on centers. The beams have a span of 4.2m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameter bars in two rows with 25mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places =
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It is reinforced with 4-36 mm diameter bars at the tension side of the beam placed 75 mm above the bottom of the beam. f = 25 MPa, fy = 414 MPa, E, = 200,000 MPa. Which of the following is the nominal moment capacity of the beam.