2. An electrician experienced a mild shock when he accidentally touched a wire carrying 5.0 A for 1.5 s.  a. How many coulombs of charge flow through the electrician?  b. How many electrons constitute the given current?

Check your understanding A. Solve the problems below. You are required to show the proper solution with the final answer written inside a box. Make sure to put the final unit of measurement. 1. If in the process of rubbing the lenses of the eyeglasses, 6.28 x 10 10 electrons were transferred, a. what is the charge of the lenses and the nylon cloth? b. what is the change in their masses? CS Scanned with CamScanner

5. A 250-volt electrical heater is used to warm 3Li/hr of water from 19°C to 98°C. Assume heat conversion loss of 25% of the total heat supplied, how much current in amperes must be supplied to this heater. Derive with the formula below, show the cancellation, explain the step by step and DRAW a free body diagram/figure. refer with this: PE1 + KE1 + U1 + WF1 + Q1 + W1 = PE2 + KE2 + U2 + WF2 + Q2 + W2 + E losses.

The filament of a certain light bulb is made of tungsten and has a length of 0.48 m and a circular cross-section with a diameter of 0.062 mm. a. Calculate the resistance of the filament at room temperature. b. A4.0 V voltage applied to the filament results in a 0.078 A current. Determine the temperature of the filament under these conditions. I need to show all work please

Solve the problems below. Make sure to show proper solution. All finalanswers should be written inside a box.  3. The electric field of the material between two coaxial cables of radius .25 m and .51m is given as E = 2.58 V.m/r3. If the conductivity of the material is 5 x 1010 S/m, whatis the current density in the material?

m 2R R 3. The new symbol you see in the diagram at the left is a multicell battery (like a 9V), which is made up of a number of smaller single cell batteries (like a 1.5V). Let's say its total voltage is V. A. Which resistor takes the most voltage? B. What is the total resistance? C. In variables, what is the current in the circuit? D. How does the voltage used by the 2R compare with R? E. In variables, what is the voltage used by the 2R resistor?

Only 100% sure experts solve it correct complete solutions need okk.dont use chat gpt okk. Electronic subject it is okk. Only qno2 solve

Solve the problem. Show pertinent solutions.

What to do: Answer the following problems. Write your solutions in a separate sheet of paper. 1. Compute the equivalent resistance of the network in the circuit shown below. Show the steps in reducing a combination of resistors to a single equivalent resistor. The source of emf has an negligible internal resistance. E = 18 V, r = 0

Capacitance, Charge and Voltage: Q = CV 1. Click the Reset Button on the bottom right of the PHET simulation. 2. CHECK Plate Charges and Bar Graphs boxes in the upper right so your display resembles the graph below. 3. SET the Plate Area to 200 mm² and the Separation to 4.0 mm. Capactance Tup Pate Charge oc Sured Energy Pu Charges r Graphs O e Fd Cument Direction 1500 V 4. Connect the voltmeter across the capacitor by placing the red on the top plate and black on bottom. If the voltmeter reads a negative, switch the red and black. 5. Set the battery Voltage to 0.25 V. Record the measured plate charge, Q. 6. Repeat Step 5 for each Voltage in Table 3. Table 3: Charge and Voltage Voltage |(V) Plate Charge |(pC) 0.25 V 0.50 V 0.75 V 1.00 V 1.25 V 1.50 V