2. A series RL circuit has voltage and current equations of e = 141.42 sin 2n30t + 141.42 sin 2n90t volts and i = 9.8 sin (2n30t - 30°) + 5.66 sin (2n90t - 60°) amperes. Determine the inductance L. A. 92.5 mH B. 38.3 mH C. 27.22 mH D. 83.49 mH

2. A series RL circuit has voltage and current equations of e = 141.42 sin 2n30t + 141.42 sin 2n90t volts and i = 9.8 sin (2n30t - 30°) + 5.66 sin (2n90t - 60°) amperes. Determine the inductance L. A. 92.5 mH B. 38.3 mH C. 27.22 mH D. 83.49 mH

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: 1 ohm 3 ohm 5 ohm www 120 V 20 AO 11.43 A 15.5 A 10.4 A

Q: Assume that the 4-bit bidirectional shift register in the figure below initially contains 0011, and…

A: The bidirectional shift Register moves the data either to right or left based on the control bot…

Q: For how long must a charging current of 2 A be fed to a 5 µF capacitor to raise the p.d. between its…

Q: 25 V (3) (c) 15 V 10 V 100 Ω 47 02 Μ 16. For each circuit in Figure 8-76, determine the Thevenin…

A: Since you have posted the multiple questions so we are supposed to answer three questions. We need…

Q: R3 6Ω www R₁ 692 www R₂ 12 92 1.25 F HH + vc (1) - R4 10 22 + vo (1) Fig. 3. For the circuit in Fig.…

Q: Give a detailed account of the pontetial of underground and submarine XLPE cable. Include the…

A: We have to give detailed account of the pontetial of underground and submarine XLPE cable. In…

Q: In the circuit shown below for I1=25 A,R1=775, R2=485 and K=2, find the following: 11 1) Vo= 2)…

A: In this question We need to determine the unknown parameters. We know Power P= Voltage × current

Q: mmc UD D in ne IN T זרזבט רזבײַזומ ממזונור מרמנcבסי Q.94 For a 3.6°, 2-o bipolar stepper motor, the…

A: Given- A 3.6o, 2-ϕ bipolar stepper motor- Stepping rate=200 steps/second, To Find- The rotational…

Q: Problem #4) Given the following (steady-state) AC circuit: Is V = 120/0° volts Vs 10-j10 Ohms j10…

A: In this question We need to determine the all unknown parameters. We know Current in the impedance…

Q: 1. For the unitary feedback closed-loop system with a proportional K gain controller C below R P(s)…

A: Given: Ps=1s+1s+2s+9s+10,Controller Gain=K.

Q: 1. Determine the functions f (t) having the following Laplace transforms using HET: F(s): S (s+ 2)²…

Q: 1. Calculate the theoretical output DC voltage of the half-wave rectifier circuit and compare it…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Find the output y(n) given the difference equation and input signal. Difference equation: y(n) =…

A: Given: Difference equation, y[n]=2x[n]+3x[n-1]-x[n-2]+y[n-1], Input signal, x[n]=[1, 2, 4, -1, 5,…

Q: Determine which differential equation best represents the system described by the block diagram…

A: We need to find out differential equations for given system .

Q: For how long must a charging current of 2 A be fed to a 5 µF capacitor to raise the p.d. between its…

Q: ) Determine whether the systems with the following transfer functions are (internal) stable,…

A: Given Data: A set of transfer functions such as, Gs=s+2s+1s-1 Gs=1s2s+1 Gs=1ss+1 Gs=1s+1s+2 To…

Q: Which of the following systems is/are both linear and time-invariant? a. y[n] = ay[n − 1] + x[n] b.…

A: Option (b) is not linear because it does not satisfy the superposition property. If we apply a…

Q: Draw the straight line characteristics of the alternators in the graphing space below ?

A: Answer: To draw straight line or short circuit characteristics of Alternators

Q: Plot the input/output characteristic of the circuits illustrated in Fig. assuming a constantvoltage…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Which of the following describes the signal shown below? x (1) 2 O a. O b. O c. O d. -3 1 0 3 3r(t +…

A: We need to write the given signal in term of step and ramp function.

Q: Find VBE, ic, ib, ie assuming Beta is 50.

A: The required parameters can be calculated by using the DC analysis of the amplifier circuit. By…

Q: Let x(t) = u(t)-u(t-1) and y(t) = u(t)+u(t-1)-2u(t-2) a) plot x(t) and y(t) b) evaluate graphically…

A: First plot x(t) and y(t). Now using convolution integral find expression for signal z(t). Now using…

Q: For the timer curcuit above, the duty cycle of the square output wave measured at pin3 is? a)31.25%…

Q: 4₁ (t) = (it) mm LI Y21t) R₁ gilt) R2 mm R3 +1 Vlt) = U₂lt)

A: State Space Equations d x(t)dt = [A] x(t) + [B] u(t)y(t) = [C] x(t) + [D] u(t) x(t)→state…

Q: Wouldnt the peak voltage in the secondary half be 1/3 x 1.414 x 120? 56.56V divided by 2 28.28…

A: The given circuit is a center tapped full wave rectifier and the required parameters can be…

Q: 4) Find the current (Note: there is a current-dependent voltage source here) Determine in the…

Q: CLK X Y Z X R Y Z Consider the following digital logic design that has a D-FF in it: D D CLK F D…

Q: Q.9 } In a system of 132 kV the line to ground capacitance is 0.05 µF and the inductance is 8 H.…

A: Given- A system of 132 kV, Line to ground capacitance = 0.05 μF Inductance = 8 H, Magnetizing…

Q: Explain any two Passive transducers with neat diagram. Note: don’t write by hand diagrams should be…

A: We need to write about passive transducer The passive transducer is a transducer, which creates…

Q: Figure 1Ω ww 350 Ω 40 www v < 1 of 1 Part A Use the node-voltage method to find how much power the…

Q: If Vs = 7 V, R1 = 35 2 and R2 = 83 92, what voltage would you expect to see displayed on a voltmeter…

Q: The current across a 10 mH inductor is given below: a) Find the corresponding voltage. b) Over the…

A: Given: Current across 10 mH inductor is, To find: a) Corresponding voltage. b) Power transferred…

Q: Answer Question1 D,E,F please

A: In this question we need to find the Laplace transform of the given signal.

Q: Question No.99 An Amplifier has open loop gain of 20. The gain of the feedback path to operate…

A: Given: An amplifier has open loop gain, A = 20. The amplifier is operated as an oscillator.

Q: i)What are full-compensation, under-compensation, and over-compensation of arc suppression coil…

A: To explain: i) Full-compensation, under-compensation, and over-compensation of arc suppression coil…

Q: Using Kirchhoff's laws calculate the power consumed by the 2002 resistor.

A: The required parameters can be calculated by using the mesh analysis and the mesh equation can be…

Q: B. step. Convert the decimal number (48.375) 10 to binary. Show your work step by

A: In this question we need to convert the given decimal numbers into binary

Q: How does the system put its powers to use?

A: Given: How does the system put its powers to use?

Q: 4.2-1 A DSB-SC modulation generates a signal p(t) = Acm(t) cos (wct+0). (a) Sketch the amplitude and…

Q: Determine the system output y in terms of the system input x and noise n. x + ax+n 1+ab O a. y O b.…

Q: 202-4] Problem 21 A sequence zal is such that z2-n) yields the following plot. Express the following…

Q: + AV 20 ΚΩ VBE H₁ 100 Ω ΑΛΕ 6V

Q: Determine the system output y in terms of the system input x and noise n. O a. x + y = ax+n a b n y

Q: An RLC series circuit has a voltage source given by E(t) = 20 cos (24t) V, a resistor of 216 £2, an…

A: Given,For a series RLC circuit,Voltage source, Et=20 cos24t V.Resistor, R=216 Ω.Inductor, L=6…

Q: 27) The total resistance of a 4Q and a 2Ω resistor connected in parallel is: Α) 6Ω Β) 1.3 Ω C) 8Ω…

A: option b To calculate the total resistance of two resistors connected in parallel, you can use the…

Q: For the circuit shown, the current flow thro... For the circuit shown, the current flow through R3…

Q: . A 25-cycle transformer has 2,250 primary turns and 150 secondary turns. If the maximum value of…

Q: What are the advantages of parallel operation ofalternators ?

A: Parallel Operation of Alternators :- Electric power systems are interconnected for economic and…

Q: Given vectors from the origin r = 3a, + 8a, + a₂, r = a, - 6a, + 5a,, and rc = 7a, - 48., find: (a)…

A: Given that , rA=3ax+8ay+az rB=ax-6ay+5ay rc=7ax-4az We need to find the unit vector perpendicular to…

Q: Find the SSE for a unit step and unit ramp functions of the following

A: Given: A control system, To find: Steady state error for unit step and unit ramp functions.

Question

2. A series RL circuit has voltage and current equations of e = 141.42
sin 2n30t + 141.42 sin 2n90t volts and i = 9.8 sin (2n30t - 30°)
+ 5.66 sin (2n90t - 60°) amperes. Determine the inductance L.
A. 92.5 mH
B. 38.3 mH
C. 27.22 mH
D. 83.49 mH

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
What is the value of capacitance if the capacitive reactance is 50 Q .Assume frequency of supply as 50 Hz ? a. 53.3x10-5 F O b. 5.3x10-5 F c. 6.36x10-5 E d. 63.3x10-5 F
QUESTION 50 RG180B/U is a coaxial cable with a nominal impedance of 95 02 and a capacitance per foot of 15.5 pF/ foot. Determine the inductance per foot of this cable. O a. 140 nH/ft Ob.45 nH/ft O c. 95 nH/ft O d.250 nH/ft
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
"If lab is equal to 595.8252306 and lb is 344296, the phase sequence is:" O POSITIVE O NEGATIVE
58. Two capacitors, a 20 µF and a 30 µF, are connected in series to a 60-Hz source. What is the total capacitive reactance? a. 117.96 N b. 221.04 N c. 253.05 N d. 333.16 N
SINUSADAL ALTER UATING SIDES 5CM 471t is APPUED TO A H. 5cm IS WOUND HTH 300 TU IN 3.) A SINUSODAL ALTERUATING SINUSADAL ALTERNATING VOLTAGE HAC N C.m.s VALUE OF 200 V FREQUENCY OF so Hz. IT THE ZERO AXIS IN A CROSSES POSITIVE DIRECTION KHEN t=0. DETERMINE li) THE TIME WHEN VOLTAGE FIRST REACHES THF STANTANEOUS VUE OF 2wY AND (i) THE TME HEN KOUAGE LETER PASSING THROUGH Ts MAXIMUM POSITIVE YALUE REACHES THE VALUE 11141.4 V. (0.0025 SELOND (ii) 1/300 SECOND) OF 200 SN 47 E iS APPUED TO A HW AN ALTEFNSTNG VOLTAGE SEPIES VITH A KRISTANE OF 40 2.IF THE
The ripple factor for pure dc is Answer:
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is