Probable Error-a.b.Example 2PLANE SURVEYINGSU1200ASSIGNMENT 11. The sides of a closed figure have been measured and found to have a total length of 1018.910 m.If the error in the measurement is estimated to be 0.073 m, what is the accuracy ratio of the work?2. A random error of ± 0.004 m is estimated for each of 22 length measurements (which are to beadded together to get the total length).what is the estimated total error?what is the probable total error if the random error is ± 0.006 m per length?3. A surveying crew or party is capable of taping distances with an estimated probable error of ± 0.005for each 30.000 m distance. What estimated total error should be expected if a distance of 1400 mis measured?4.It is desired to tape a distance of 360 m with a total estimated probable error of not more than ±0.006 m.a. How accurately should 30.000 m distance be measured so that the permissible value is notexceeded?b. How accurately should each 30.000 m distance have be measured so that the estimated

Note : Question 2 is circled, so solving only circled question. - Calculate the estimated total…

2. A random error of ± 0.004 m is estimated for each of 22 length measurements (which are to be added together to get the total length). a. what is the estimated total error? b. what is the probable total error if the random error is ± 0.006 m per length?

2. A random error of ± 0.004 m is estimated for each of 22 length measurements (which are to be added together to get the total length). a. what is the estimated total error? b. what is the probable total error if the random error is ± 0.006 m per length?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a. Two points A and B (distance =100m) were nominated at the field and Two points A and B (distance =100m) were nominated at the field and At Mid Point At End Point Point A 1.477 1.626 Point B 1.055 1.201 Height Diffierence Calculate the collimation error and demonstrate with a figure. Comment on the vertical collimation error and explain how we can adjust the vertical collimation error for a levelling instrument?
Q.5 What will be the area ratio of a split barrel sampler having inside diameter of cutting edge as 35 mm and outside diameter of cutting edge as 51 mm. Take inside diameter of sampling tube as 38 mm.
An experiment was carried out to study the effect of reinforced flanges on the torsional capacity of reinforced concrete T-beams. Several different types of T-beams were used in the experiment, each with a different flange width. The beams were tested by subjecting them to combined torsion and bending to failure (elongation). Below are the results obtained for 70 cm beams and 100 cm beams (assuming normal populations) Width 70cm6.07.210.213.211.413.69.2 Width 100cm6.89.28.813.211.214.910.211.815.2 Is there evidence of a difference in the variation of torques of the two types of T-beams? Use α = 0.1
2. The heights of 1000 students are approximately normally distributed with a mean of 174.5 centimeters and a' standard deviation of 6.9 centimeters. Suppose 200 random samples of size 25 are drawn from this population and the means recorded to the nearest tenth of a centimeter. Determine (a) the mean and standard deviation of the sampling distribution of X; (b) the number of sample means that fall between 172.5 and 175.8 centimeters inclusive; (c) the number of sample means falling below 172.0 centimeters.
NEED ASAP PLS!!
The error in measuring the radius of a 5cm circular rod was 0.2%. If the cross-sectional area of the rod was calculated using this measurement, then the resulting absolute percentage error in the computed area is (round off to two decimal places) Enter Your Answer... Check
2.) ANALYZE COMPLETELY AS PRESENTED IN THE POWERPOINT LECTURE. You may not copy the problem. SUMMARIZE ANSWERS 0.9m 900N 0,6m 2.4 m 2000 N A自 0.6 1.8 1.8
if for the particular measurement of the probable error of the mean is 0.075 m and the most probable value of the measurement is 365.70m the relative precision is as
From the measured values shown, determine if the measurements are within the required precision. Show all computations. Allowable precision is 1/5000. Trials Distance (m) 1 220.87 2 220.90 3 220.93 4 220.89 5 220.81
Determine the relative precision of the mean of the measured values shown . Trials 1 2 3 4 5 Length (m) 106.87 106.90 106.93 106.89 106.81
What is the total random error in 8 measurements, if you know the single random error is + 18.0 mm? Answer: Choose...
What is the total random error in 11 measurements, if you ?know the single random error is + 10.9 mm