Please include units 2.A fire truck is sucking water from a river and delivering it through a longhose to a nozzle. The total length of the galvanized iron hose corrected for valves,fittings, entrance, etc. - is 90 [m]. The energy provided by the fire truck for pumpingthe water is 53 [kJ/kg].What diameter is needed for the hose to provide an average velocity of 30 [m/s]?riverII30 [m]pump16 Table 2.1. Roughness of Clean Pipe²€, mmPipe materialRiveted steelConcreteWood staveCast ironGalvanized ironAsphalted cast ironCommercial steel or wrought ironDrawn tubingGlassPlastic (PVC, ABS, polyethylene)1-100.3-30.2-10.26 (0.25) ¹0.15 (0.15)0.12 (0.13) b0.046 (0.043)0.001500"Adapted from Fischer and Porter Co., Hatboro, PA,Catalogs section 98-A (1947).Values in parentheses from Colebrook (1939).

There is no information provided on the flow. Therefore, we will assume that the flow is laminar…

2. A fire truck is sucking water from a river and delivering it through a long hose to a nozzle. The total length of the galvanized iron hose corrected for valves, fittings, entrance, etc. - is 90 [m]. The energy provided by the fire truck for pumping the water is 53 [kJ/kg]. What diameter is needed for the hose to provide an average velocity of 30 [m/s]? -

2. A fire truck is sucking water from a river and delivering it through a long hose to a nozzle. The total length of the galvanized iron hose corrected for valves, fittings, entrance, etc. - is 90 [m]. The energy provided by the fire truck for pumping the water is 53 [kJ/kg]. What diameter is needed for the hose to provide an average velocity of 30 [m/s]? -

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Enumerate the remaining measurement quantity and Unit

A: Time-si unit second, length-si unit meter, mass-si unit kilogram, electric current-si unit…

Q: Write short notes on significance of grashoff number.

A: The answer is given below

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

Q: complete the missing lines in the figure below 8.

Q: If the main scale reading (mm) and vernier scale reading (division) are 27 and 47 respectively for a…

A: Given: main scale reading = 27mm vernier scale division = 47 division total division on vernier…

Q: Find ex, ey and y. NOTE: ex and ey in mm/mm and y in radians.

Q: Express the quantity 556.2 x 10^-12s in fs.

A: Given Data: The time given is t = 556.2×10-12 s. The conversion of second to femtosecond can be…

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: Draw chalk diagram of all sections

A: To draw section views

Q: A wind turbine has a power coefficient C, = 0.46 and is able to generate 1.6 MW. What was the amount…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Convert the decimal number 11510 into its octal number equivalent

A: Convert Decimal to Octal with Steps Write the given decimal number. If the given decimal number is…

Q: Write the following as full (decimal) numbers with standard SI units. b. 10cm c 1001 g d. 48cl

Q: Round number to three significant figures. 1.548937 x 10^7

A: For scientific notations significant digits/figures are calculated only for the coefficient or…

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

Q: Show a scale diagram indicating a reading of 0.206 inch in a micrometer.

A: Given question : Show a scale diagram indicating a reading of 0.206 inch in a micrometer. The…

Q: G R.75 00.63 THRU E 01.123 F0.250 T 2.00 1.00 1.38 1.123 mm diameter hole with depth of 0.250 mm…

Q: A wind turbine has a power coefficient C, = 0.25 and %3D is able to generate 1.3 MW. What was the…

A: Given Wind power generated, P = 1.3 MW Power coefficient = 025

Q: Can I get a more detailled explenation on how to get the numbers in the numetor in each fraction…

Q: 1. show all steps in detail, units and formulas please.

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: Create a table showing wrench sizes in metric and U.S. units.

A: Following are the wrench sizes in metric and U.S. units.

Q: Completely solve and box the final answer. Please show the units to show the unit cancellations.…

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: The beam in the figure below is subjected to a load P= 3.9 kN at its end. Young's modulus is 210 GPa…

A: P = 3.9 kNE = 210 GPa I = 5 * 106 mm4a = 1.5 mb= 1.3m

Q: w In an engine, the piston diameter is 3 1/4 inches, the stroke is 4 7/8 inches, and the piston…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: 1.5 mm + 2.0 mm 2.0 mm 3.0 mm A shear force, S, is applied. This results in shear flow, shown with…

A: Shear flow at a junction is analogous to current at a junction. That is, the total amount of shear…

Q: What is an inflection point?

A: In solid mechanics, an inflection point is defined as a point where the curve of a physical quantity…

Q: SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE…

A: To mark the letters on the following figure mentioned.

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

Please include units

2.
A fire truck is sucking water from a river and delivering it through a long
hose to a nozzle. The total length of the galvanized iron hose corrected for valves,
fittings, entrance, etc. - is 90 [m]. The energy provided by the fire truck for pumping
the water is 53 [kJ/kg].
What diameter is needed for the hose to provide an average velocity of 30 [m/s]?
river
I
I
30 [m]
pump
16

Table 2.1. Roughness of Clean Pipe²
€, mm
Pipe material
Riveted steel
Concrete
Wood stave
Cast iron
Galvanized iron
Asphalted cast iron
Commercial steel or wrought iron
Drawn tubing
Glass
Plastic (PVC, ABS, polyethylene)
1-10
0.3-3
0.2-1
0.26 (0.25) ¹
0.15 (0.15)
0.12 (0.13) b
0.046 (0.043)
0.0015
0
0
"Adapted from Fischer and Porter Co., Hatboro, PA,
Catalogs section 98-A (1947).
Values in parentheses from Colebrook (1939).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Make the indicated conversion between customary and metric units of weight and mass. 17 kilograms to ounces
hii, what's the right formula for n? h2 will be subtracted in the numerator too as well as in the denominator, or not?
Please help I will give you good ratings
Solidworks
Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The material is Vanadium. (Located in the "Other Metals" folder in the material properties.) A = 1.72 B = 1.4 2.40 1.20 T .75 TYP 1.20 TYP .70 -1.00 TYP A A A+3.25 R.35 TYP -R.65 TYP CBORE FOR 5/16 HEX HEAD BOLT Ø.332 THRU ALL LØ813 V 235 .10- SECTION A-A 23. B B+1
Find the Ixx value for the plate as shown below, where b1=d2=18 mm, d1=85 mm,b2=65mm. (ENTER ONLY THE VALUES IN THE BOXES BY REFERING THE UNITS GIVEN IN THE BRACKET) b1 b2 d2 d1 O The X value (unit in mm) =.
i) The displacement at point A. Enter your answer in mm to 2 decimal places.
Please only answer number 8
Pls do stepwise and correct.
Q6 Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length of 400 mm. What is the engine capacity in litres? Give your answer to 2 decimal places.