2. A facility manager replaces all the TS lights in an office when they have reached 80% of their rated life of 20,000 hours. The lights operate for 12 hours each day, 5 days per week for 52 weeks of the year. What is the group re-lamping interval for these lights? a. 3.7 years b. 4.6 years C. 5.1 years d. 6.4 years

2. A facility manager replaces all the TS lights in an office when they have reached 80% of their rated life of 20,000 hours. The lights operate for 12 hours each day, 5 days per week for 52 weeks of the year. What is the group re-lamping interval for these lights? a. 3.7 years b. 4.6 years C. 5.1 years d. 6.4 years

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter1: Electrical Safety

Section: Chapter Questions

Problem 7RQ: Which of the following is the standard by which electrical installations are measured in the United...

See similar textbooks

Similar questions

You have an LED night light without a photocell control with the following information: It draws 0.3 Watts continuously. It is always on--24 hours per day. Based on this information, we can now calculate the energy used by this nightlight in one year. For this problem we will assume a year to consist of 365 days. (It is not a leap year.) Calculate the energy used by this night light in one year. Group of answer choices 0.1095 kW-hrs 0.365 kW-hrs 0.003 kW-hrs 2.628 kW-hrs
Two 115-V incandescent lamps A & B are connected in series across 230-V de source. Lamp A is rated 100 W and lamp B is rated 60 W. Which lamp is abnormally bright and hence will burn out soon? a) Lamp A b) Lamp B c) Both lamps will be abnormally bright d) Both lamps will work normally
a.) Explain briefly why the resistance of the lamp increases as the voltage is increased.b.) Explain briefly what happens when load resistances are being removed one at a time in aparallel connection. Thank you.
Vdc0 U=12 V Circuit #1 Ried V LED www Ried_series 0.05 Vdc0 U = 12 V 0,04 Circuit 0.03 0.02 0.01 RED LED GREEN LE Set current to 10 mA LED voltages Given the circuit #1 presented above, answer the following questions: BLUE_LEC Red 0.5 1) Determine the value of the V₁ (voltage forward of the LED) for the LEDS RED, VDRED GREEN, VREEN and BLUE, VOBLUES when the current through the LEDs is 10mA, 2) Is the LED in Circuit #1, connected in the way that will be lighting up or not - Justify your answer Green 3) Calculate the value of the resistance Rled in Circuit #1, to ensure that a RED LED will have a current of 10 mA 1.5 2 25 Voltage across LED (V) 4) Calculate the value of the resistance Rled in Circuit #1, to ensure that a GREEN LED will have a current of 10 mA Blue 5) Calculate the value of the resistance Rled in Circuit #1, to ensure that a Blue LED will have a current of 10 mA 6) Given three LEDs, connected in series as shown in the Circui # 2 (below), calculate the value of the…
What are the protection coordination procedure of circuit breakers
A question from the Matallb I want a solution in half an hour.
methodology used to know how many people pass through the place where the tiles will be installed ELECTRICAL POWER GENERATING PIEZOELECTRIC TILES
leaving a freevway. Current from the opposite side must travel further, weakening the potential on that side. This creates a potent the motor in that direction, causing the motor to spin. O Only the side where the switch is closed forms a cormplete circuit, so the motor must spin in that direction. Answer the questions and submit the photos for questions 2 -9using the circuit from STEP 2. D2 Yellow R1 50 Q R2 50 0 R3 PSB (+ 5 V 100 aLW R4 D1 100 Q Blue SW1 Sw2 Question 2 本

What is the greatest voltage that can be applied across a -W, 2.7-MQ resistor without causing it to overheat?
There are 32 solar cells in the solar system, and each one has the qualities listed below: Voc is set at 0.75 volts, while Isc is set at 2 milliamperes. Open circuit voltage and short circuit current will be if all four cells are in series and the groups are linked in parallel.
We want to measure the amount of current flowing to an old light bulb. We expect that the result will be around 5A. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SUDE SWITCH: LEFT- OFF MIDDLE- DCVOLTS DC mA NUMERICAL VALUE OF VOLTS OR mA OR OHMS DISPLAYED HERE 0.00 OHMS RIGHT - AC VOLTS AC mA OFFOD AC DC-A DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 200 (SELECT RANGE) 2K. 20K. •200 20u MOVE ROTARY SWITCH TO THIS AREA TOo READ mA (SELECT RANGE) 200K 20u *200u m 2M 20M 200m 20m 10A COM vn PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin. NOT CONNECTED
How does the magnitude of the voltage across the power supply compare to the voltage across the bulb with the switch open? How do they compare with the switch closed?