2. A 6-kg mass falls 0.80m and strikes the head of the steel bolt of length 1.50m. Assuming all the energy is absorbed by the 20mm diameter bolt, compute the required thickness t of its head if the shearing stress on the cylindrical surface through the head is not to exceed 80 Gpa. Assume E = 200 GPa. 20mm bolt mass 0.80m t of the head

2. A 6-kg mass falls 0.80m and strikes the head of the steel bolt of length 1.50m. Assuming all the energy is absorbed by the 20mm diameter bolt, compute the required thickness t of its head if the shearing stress on the cylindrical surface through the head is not to exceed 80 Gpa. Assume E = 200 GPa. 20mm bolt mass 0.80m t of the head

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a torsional resistance TA. Also, soil along the sides of the pipe creates a distributed frictional torque along its length, varying uniformly from zero at the surface B to tA at A. Determine the minimum torque TB that must be supplied by the drive unit to overcome the resisting torques, and calculate the maximum shear stress in the pipe. The pipe has an outer radius ro and an inner radius ri.
A thin rim1.6 m external diameter is 160 mm wide and 12 mm thick. It is made in two halves with the joint parallel to the axis, and fastened together by three bolts on each side of each joint. If the maximum allowable shear stress in the bolts is 16 MPa. Determine for a speed of 500 rev/min : a) The centrifugal stress in the rim . assume  = 7.8 Mg/m3 b) a suitable diameter for the bolts, if they are in single shear.
A steel shaft 100mm in diameter is loaded and support in shaft bearing 0.4m apart. The shaft carries three loads: first mass 12kg at the centre, second mass 10kg at a distance 0.12m from the left bearing and third mass of 7kg at a distance 0.09m from the right bearing. Find the value of the critical speed by using Dunker ley’s method if E = 2X1011N/m2.
A hole punch for plaster board consists of a spring loaded sharpened cylinder as shown. The spring is compressed 50 mm from a free length and when activated punctures the wall. If the hole punch is to be designed with a 100 J impact energy determine the spring stiffness in kN/m
..A crane is to raise a load of 25,000 N at an acceleration of 1 m/s2 through a 6 x 19 wire rope whose weight is 15,000 N. The diameter of the rope is 32 mm and the rope drum diameter is 960 mm. Take the Young’s modulus for the wire rope as 80 kN/mm2. Assume dw = 0.063 d. Which of the following is the bending load of the wire rope? Group of answer choices 61 kN 40 kN 4 kN 80 kN
I need the answer as soon as possible
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
2.2 A thin rim 1.8 m diameter and 160 mm wide, is made of steel plate 13 mm thick. The rim is made in two halves with the joints parallel to the axis. Determine the centrifugal stress produced in the material at a speed of 450 r/min. Density of steel is 7800 kg/m³. The two halves are fastened by three bolts on each side of the joint, the bolts are 21 mm in diameter and are in single shear. Determine the shear stress in each bolt when the rim is rotating at 450 r/min.
A coupling must transmit 30 hp at a speed of 175 r/min. 3/8 inch diameter bolts are arranged in a single 6 inch diameter circle. The shear stress in the bolts should not exceed 5,000 psi. What is the minimum number of bolts that should be used? Answer: seven bolts
In a pipe of diameter 100 mm, carrying water, the velocities at the pipe center and 30 mm from the pipe center are found to be 2.5 m/s and 2.2 m/s respectively. Find the wall shearing stress.
A vertical shaft 25 mm diameter and 0.75 m long is mounted in long bearings and carries a pulleyof mass 10 kg midway between the bearings. The centre of pulley is 0.5 mm from the axis of theshaft. Find (a) the whirling speed, and (b) the bending stress in the shaft, when it is rotating at 1700r.p.m. Neglect the mass of the shaft and E = 200 GN/m2.
Asap