2. A 12mmx400mm steel plate has staggered holes arranged as shown. 60 "b" mm 12 -01 100mm Pu Pu 400 100mm 100mm 150mm a. Calculate the distance "b" so that the net area in path 1-2-3-4 is equal to the net area of path 1-2-4? b. Using the computed value of "b", solve for the critical net area. c. Calculate the ultimate safe tensile force Pu that the steel plate could carry?

2. A 12mmx400mm steel plate has staggered holes arranged as shown. 60 "b" mm 12 -01 100mm Pu Pu 400 100mm 100mm 150mm a. Calculate the distance "b" so that the net area in path 1-2-3-4 is equal to the net area of path 1-2-4? b. Using the computed value of "b", solve for the critical net area. c. Calculate the ultimate safe tensile force Pu that the steel plate could carry?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.1P

See similar textbooks

Similar questions

Determine the elongation of the steel bar shown. B A 1. ds L P-416 KN L-875mm E-200 GPa dA= 250mm d 600mm Answer in trin and in 5 decimal places (e, O.20205mm)
Please solve sub-part- ii completely and accurate with correct calculations. Thank you!
EN O Aロa。 USEFUL LINKS v M Time Select the reinforcing needed for the short tied column shown for the following: Pn=2000 kN, 250 mm, e 200 mm. f28 MPa, fy= 420 MPa: (Add attachments below) 70 s00 mm 640mm 70 mm 70 mm 70 mm 210 mm 350 mm
An A36 axially loaded 13mm thick tension member is connected to a gusset plate using 5pcs 18mm diameter rivets arranged as shown. Use Fy= 248MPa & Fu=400MPa for the steel plates. Given a=81mm, b=58mm, c=98m, x=80mm, y=84mm and z=91mm. Calculate the net area in mm2 on Path ABE Express your answer in 2 decimal places.
P= 430N M= 860 N•m M 1 m 1 m B m find: Cx & Cy P -2 m- Show Transcribed Text A
Determine the centroidal z-coordinate (in mm, round=off to 2 decimal places) of the wire figure shown.
Two 10inch-15.3 lb channels are welded together as shown in the figure. Compute for the values of Centroids, and lxx for the figure. 1. Determine ybar? 2. Determine lxx (Centroidal)
A cantilever beam shown in Fig , with rectangular section shown. Its carry uniform load wand concentrated load Pa =12 KN, F-0.5. a- Calculate the instantaneous and 6- years long-term deflections at free end b- Check the deflections with ACI-Code limitations. 012 stirrups 60 29 h 2429 K-bw fy bw, W, kN/m² h, mm Wa mm 20 350 155 1.75 | 8.5 | 1.6 500
There is a statically indeterminate beam in which the horizontal force at the left and right ends (points A and D) is zero, and the vertical force is shown in the figure below, The flexural stiffness of the beam section is constant El: Try to find the slope (Slope) of point B after deformation.
4.5.12 OIC Section Properties Write functions for A, I, c, radius of gyration. Each function works for the three sections below. Example Function name: OICSEC_A() • OICSec_() Etc. 을 + 12 BIP - bhs V, 12(BII-bh) BII -- bha 6/1 - 8
For the given properties of the beam below, determine the safest wy that the beam will carry. bf = 850mm bw = 400mm tf = 100mm d = 400mm ニ d' = 100mm fc' = 32MPA %3D fy = 400MPA As = 8 - 32mm bars ニ The answer is kN/m Pu = 20 KN %3D bf 3Pu O-50 Pu 七キ Wu 5m As 13 + bw *
A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The holes are 2mm larger than the bolt diameter. The plate is A36 steel. Bolt diameter is equal to 34mm. It is required to determine the value of “b” so that the net width along bolts 1-2-3-4 is equal to the net width along bolts 1-2-4. Given: Fy=248MPa, Fu=400MPa Required: 1. Determine the value of “b” in millimeters. 2. Determine the net area for tension in plates in square millimeters. 3. Determine the design strength for LRFD. 4. Determine the allowable strength for ASD.