2) The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. When the applied load is 45 KN, the new diameter of the specimen is 12.48375 mm. Compute the shear modulus (Gal) for the aluminum. σ (MPa) 500 [1 0.00614 € (mm/mm)

2) The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. When the applied load is 45 KN, the new diameter of the specimen is 12.48375 mm. Compute the shear modulus (Gal) for the aluminum. σ (MPa) 500 [1 0.00614 € (mm/mm)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stress-strain diagram for an aluminum alloy specimen having an original diameter of 0.5 in. and a gauge length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 60 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded.
As a result of the tension applied from the base in the X axis, the strain value of the structure in the same direction was measured as 0.26 mm / mm. Under the same loading condition: a) Calculate the strain of the structure in the Z axis. b) In this case, what is the type of strain on the Z axis?
An aluminium tensile test specimen has a diameter, d = 25 mm and a gauge length of Lo = 250 mm. If a force of 175 KN elongates the gauge length by 1.25 mm, the moduls of elasticity of the material is nearly
The error in a measurement due to strain when using a tape measure depends on the material that it is made of. For a tape with a cross section of 10 mm by 0.7 mm, calculate how much error is introduced in inches into the measurement at a 300 ft length if the tape is pulled with 80 N and if the tape is made of: a) mild steel (E = 30 x 10^6 psi), b) polycrystalline aluminum (E = 10 x 10^6 psi) c) fiberglass composite (E = 3.5 x 10^6 psi in the long direction)
The elastic portion of the tension stress–strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gage length of 2 in. and a diameter of 0.5 in. If the applied load is 10 kip, determine the new diameter of the specimen. The shear modulus is Gal = 3.811032 ksi.
A strain gauge is used to measure the shear strain on a shaft during torsional loading. The strain gauge is mounted such that it measures strain at an angle of 45° to the longitudinal axis of the shaft. The shear strain in the shaft is determined: a. as the strain measured by the strain gauge O b. by dividing the strain measured by the strain gauge by the shear modulus O c. None of these options O d. as twice the normal strain determined by the strain gauge.
In a tensile test for an aluminum alloy, the sample used is 2 inches long and 0.5 inches in diameter. The proportional portion of the tension stress-strain diagram for an aluminum alloy is shown below. _x106 lb/in² Pay attention to units and calculate your answer to 1 decimal place for the unit specified above. σ (ksi) 70 t 0.00614 Determine the modulus of elasticity for this material: € (in./in.)
pleae writte by hand step by step
None
A strain gauges system mounted at a point on a structural member that is subjected to multiaxial stress, where we have the following readings: Ex = 3.8 x104; &y = 5.5 x10-5; Ez = - 7.5 x10-5; Yy = 9.1 x104; %3D Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 200 Gpa and Poisson's ratio v = 0.3; Select one: Ох %3D -100 Мра; оу %3D -50 Мра; о, %3D 30 Мра; Тху 3D 70 Мра; Ox = -75 Mpa; o, = -50 Mpa; 0z = 40 Mpa; Ty = 80 Mpa3; Oy = 300 Mpa; oy = -150 Mpa; 0z 3 100 Мра;B тyу = 100 Mpa; TOSHIBA
Q // The tensile tests were performed on longitudinal specimens of compact bone. The E1= 0.0004 65° strain rosette is mounted on a bone were the readings are obtained for each gauge as shown in figure. Determine (a) the principal strains and (b) the shear strain and average normal strain. 50° E2 = - 0.0005 65° €z = 0.0003
A strain gauges system mounted at a point on a structural member that is subjected to multiaxial stress, where we have the following readings: Ex = 3.079 x1o-3. ; Ey = -3.471 x10-3; Ez = 1.207 x10-3; yxy = 3.743 x10-3; Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Young's modulus E = 70 Gpa and shear modulus G = 26.7 Gpa;