2 Load-Line Analysis 1. a. Using the characteristics of Fig. 152b, determine Ip, Vp, and Vg for the circuit of Fig. 152a. b. Repeat part (a) using the approximate model for the diode, and compare results. c. Repeat part (a) using the ideal model for the diode, and compare results. Ip (mA) 3어 25 E= 12 V R20.75 kf2 VR 20 15 (a) 10 -0 8. 10 11E 12 VoV) 4 9. 0.7 V (b)

2 Load-Line Analysis 1. a. Using the characteristics of Fig. 152b, determine Ip, Vp, and Vg for the circuit of Fig. 152a. b. Repeat part (a) using the approximate model for the diode, and compare results. c. Repeat part (a) using the ideal model for the diode, and compare results. Ip (mA) 3어 25 E= 12 V R20.75 kf2 VR 20 15 (a) 10 -0 8. 10 11E 12 VoV) 4 9. 0.7 V (b)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
What is the difference between a diode and rectifier?
B Answer all the questions. (1) The ms value of the input voltage for a bridge network is shown in the following figure. (a) Sketch Vo and determine average output Vo for the configuration of the following figure. (b) Determine the de voltage and r.m.s voltage of output. (c) Determine the required PIV rating of each diode. (d) Does this network work as a clipper? Ideal diodes 170 V 2.2 k2 2.2 ka -170 V 2.2 ka Sketch V and K
The cut-in voltage for each diode in the circuits shown in Figure Pl.30 is V, = 0.6 V. For each circuit, determine the diode current I, and the voltage Vo (mea- sured with respect to ground potential). Q7 R= 10 k2 Vo oVo Ip R= 10 k2 5 V 5V 5 V 5 V (a) (b) R= 10 k2 Vo 5V E 5 V (c)
Determine the điode's voltoge ond current for Hhe figure the diode's model. Find the volItage for each of Si 20 across the resistor in each case. Find the diode's power also In each case A ssume Rg is lo r.
Given the clamper circuit below, assume that the value of R and C are large enough so the voltage across the capacitor does not change significantly during the interval of time. a. Using the simplified diode model, simulate the action of the circuit when the diode is in forward and reverse bias condition and measure its output voltage. b. Draw the output waveform of the circuit. VIN +8V ER 1.3V. -8V
Q2/ Consider the circuit in below figure. What type of circuit is this? b. What is the total peak secondary voltage? c. Find the peak voltage across each half of the secondary. d. Sketch the voltage waveform across RL. e. What is the peak current through each diode? f. What is the PIV for each diode? а. 4:1 D1 120 V rms RL 1.0 kN 00400
Q1/Consider the circuit in Figure with a transformer of 10:1 transformation ratio and the diodes are silicon. a) What type of circuit is this? (b) What is the total peak secondary voltage? (c) Find the voltage value across the resistor (d) Sketch the voltage waveform across RL (e) What is the PIV for each diode? D3 D 120 V Pisez) Vpouo D D 10 kn lleee
• A Si diode at a temperature of 25°C has VD = 0.7V at Is = 10nA. The temperature is raised to 125°C. 1. Calculate ID at 25°C. 2. What is effect of rise in temperature on VD & IS 3. Calculate ID at 125°C.
In the circuit shown below, find the diode voltage VD and the supply voltage V such that thecurrent is ID = 0.6mA. Assume the diode threshold voltage is 0.3 V. Determine the powerdissipated in the diode
Question 2: (show your detailed answer for each part of questions below) a) For the series diode configuration in the figure below, determine VD, VR and Ip. + Vn Si 10V 3 kn V b) Calculate the current through a 70 2 resistor in the circuit shown in the below figure. Assume the diodes to be of silicon and the forward resistance of each diode is ta-1 2 Show the answer steps. D Dz 70 n www 20 V DA Dy