2-Force couples with an intensity of 100 N at the lowest level of the rigid body shaped to the side form the moment M. In order to obtain a moment equivalent to this moment, the existing 100 N force couples were removed and replaced by P and -P couples with 300 N intensities each. In this case, how many degrees must the angle be in order to obtain the moment value, which is equivalent to the previous situation. (Dimensions on the figure are given in mm.)

2-Force couples with an intensity of 100 N at the lowest level of the rigid body shaped to the side form the moment M. In order to obtain a moment equivalent to this moment, the existing 100 N force couples were removed and replaced by P and -P couples with 300 N intensities each. In this case, how many degrees must the angle be in order to obtain the moment value, which is equivalent to the previous situation. (Dimensions on the figure are given in mm.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using a ring collar the P = 794 N force can act in the vertical plane at various angles. Determine the magnitude of the maximum moment (Nm) it produces about point A. Round off only on the final answer expressed in 3 decimal places.
Consider the frame as shown in figure. Assume A is a pin jointed support and C is a roller jointed support. The maximum bending moment occurs at a point R, the distance of R from A measured vertically from A is 40 kN/m 4 m 80 kN 2 m 2m 3 m
A truss is loaded as shown in the figure. Assume AE = 10000
statics in rigid bodies: Complete solutions are needed. Complete equations of shear and moment at each section of the beam.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13700 ksi] rods, and a solid steel [E = 32600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.84 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.5 in. Assume L1=37 in and L2=66 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 27 kips is applied. (2) (1) L2 (1) L1 A P
A 16 N force produce a moment of 64 Nm. the moment arm is; O 8m O 4m O √2m O 2m
Solve and provide solutions with explanation
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) 1. The line of action of the 3000 lb force runs through te points A and B as shown in the figure. Determine: y scalar component of F
A rectangular tetrahedron has six sides of length 9 cm. If a force of 600 N is applied along edge BC as As shown, determine the moment of the 600-N force about edge OA. A B 600 N
Beam AC with constant EI has a roller support at point B and slider support at point A as shown in the figure below. Using the conjugate beam method to determine the magnitude of the couple moment M0 in terms of P if the displacement at point C is zero. Hint: the slider support can be considered as a fixed support but can move freely in the vertical direction. Use these properties to find the corresponding conjugate support for this problem.
Determine the reaction at the support of the beam/frea, shown in the figure using the Force Method Analysis. Draw the shear and bending moment diagram
Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the answer is negative.) The line of action of the 3000 lb force runs through te points A and B as shown in the figure. Determine the x scalar component of F?