2) For the given sections shown: 21) determine the distance of fthe centroldal avis (or neutal axis, NA) from the base or bottom of the section, 22) determine the value of the moment of inertia about the neutral axis (la) and, 2.3) determine the value of the moment of inertia about the base or bottom of the section () 10mm IG mm IG mm 1050 mm IG mm 16mm 250 m 300 mm

2) For the given sections shown: 21) determine the distance of fthe centroldal avis (or neutal axis, NA) from the base or bottom of the section, 22) determine the value of the moment of inertia about the neutral axis (la) and, 2.3) determine the value of the moment of inertia about the base or bottom of the section () 10mm IG mm IG mm 1050 mm IG mm 16mm 250 m 300 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

EXAMPLE 4.7 Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E.= 200 GPa and E.= 105 GPa, determine (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm 100 100 -180-- Dl E Steel Be 60 kN Brassc 40 kN 40-mm diam. 30-mm diam.
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
EXAMPLE 4.7 Two cylindrical rods, one of steel and the other of brass, are joined at Cand restrained by rigid supports at A and E. For the loading shown and knowing that E.= 200 GPa and E.= 105 GPa, determine (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm 100 100 -180 -15 Dl Вгass 40 kN E Steel B. 60 kN 40-mm diam. 30-mm diam.
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
The homogeneous wire ABC is bent into a semicircular arc and a straight section as shown and is attached to a hinge at A. Determine the value of e (in degrees) for which the wire is in equilibrium for the indicated position. B C Numeric Response
5.30 The homogeneous wire ABC is bent into a semicircular arc and a straight section as shown and is attached to a hinge at A. Deter- mine the value of u for which the wire is in equilibrium for the indicated position. B A
Q2-B- Fill in the blank with the correct answer. 1. When the resultant of force system acting on a body is zero, the body is said to be in (a) rotating condition (b) translation condition (c) equilibrium condition 2. Number of component of reaction at hinge support are (a) zero (b) one (c) two (d) three 3. The angle that the vector A-2i+3j makes with y-axis is 4. If angle made by the force with y and z axes are 8, = 60° and 9, = 45° then 0,= 5. Force is completely defined by its (a) magnitude (b) direction (c) point of application (d) All of these (d) dynamic condition
A force-couple system is acting on the frame as shown. Use A=80N, B=700N, C=150N, and M= 120N.m. The system is to be replaced with a single resultant force R. B 30° [Select] [Select] [Select] [Select] [Select] [Select] M 400 mm 200 mm 300 mm (a) Calculate the absolute value of the x-component of the resultant in N. (b) Calculate the absolute value of the y-component of the resultant in N. (c) Calculate the magnitude of resultant in N. (d) Calculate the angle that the resultant makes with the horizontal in degrees. (e) Calculate the absolute value of the x-intercept of the resultant's line of action in mm. (f) Calculate the absolute value of the y-intercept of the resultant's line of action in mm.
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. We know that Es=200 GPa and Eb = 105 GPa, calculate (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm -180- -120- GO KN 40-mm diam. G 1.00 100 DI Brass E 40 kN 30-imm diam.
CE - PC 311 - STRUCTURAL THEORY Quiz No. 2F - Analysis of S tatically In determ in ate Beam s 1. By the moment-area method find the slope and de flection at the fre e end A of the cantile ver beam AB. E = 30,000k/in and I = 200 in ". Re fer to the fig ure belo w. A ll decim a ls must be in c lu ded, do not round off answers. All fig ures must be included and drawn straight. Curves may be done freehand. Sum marize your answers as shown b e lo w. w kit ft ft 1.110 7 8 Required Va lu es Answer O A A L1 L2 B.
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. We know that Es=200 GPa and Eb = 105 GPa, calculate (a) the reactions at A and E, (b) the deflection of point C. A Dimensions in mm 1.00 |--10-| 180-120- GO KN 40-mm diam, Bra D 100 40 kN 30-mm diam.
The device shown is a part of an automobile seat- back-release mechanism. The part is subjected to the 4-N force exerted at A and a 300-N•mm restor- ing moment exerted by a hidden torsional spring. Determine the y-intercept of the line of action of the single equivalent force. y F =4 N 10 mm 15° 40 mm 300 N-mm