2- Calculate the values of Ro, Xo, Reg1 and Xeg1 of the equivalent circuit of a 1-ph, 4KVA, 200/400V, 50HZ transformer of which the following are test results: open-circuit: 200V, 0.7A and 70W on low-voltage (primary) side. Short-circuit: 15V, 10A and 80W on high-voltage (secondary) side. [571, 330, 0.2 and 0.3172]

2- Calculate the values of Ro, Xo, Reg1 and Xeg1 of the equivalent circuit of a 1-ph, 4KVA, 200/400V, 50HZ transformer of which the following are test results: open-circuit: 200V, 0.7A and 70W on low-voltage (primary) side. Short-circuit: 15V, 10A and 80W on high-voltage (secondary) side. [571, 330, 0.2 and 0.3172]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
Quiz2: We wish to connect a 6 kVA, 120/240 V transformer as an autotransformer to a 120 V source to supply 360 V to a load. a) Draw the circuit. b) What is the maximum load kVA that can be supplied? c) At the maximum load, determine ln, fy, and I,- d) What are the possibilities to connect it as a step-down autotransformer and determine the load voltage at cach case?
q9
Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five customers. Daily maximum demands for these customers are 120 kW, 40 kW, 90 kW, 110 kW, and 180kW. The maximum demand on the feeder is 243kW. The coincident factor of the feeder is
solution please urgent
Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
Solve it...
An OC relay having the Preset/Pickup value at 7.9 A is connected to a Current Transformer with nominal ratio =200:10 of CT, the Secondary impedance of CT is 0.092 ohm and Burden on CT is 0.9 ohm. The CT has the cross-sectional area of core to be 2.9x110-6 Cm². The current of excitation being 0.5 A and frequency of power system is 50 Hz. (Also the above CT will get saturate on the max flux density of 1.2 Tesla) (a) Solve for the E.M.F induced in the secondary of above CT. (b) Evaluate, whether the OC relay will operate or not? , when a fault current of 250 A flows in the primary line? (c) Solve the above scheme for finding the C.T saturation status (whether the CT operation is under the knee-point or beyond the knee-point of Saturation) (d) Solve for the error in CT ratio in percentage.
solve using a transformators topic At a 115 kV input transformer with 300 turns, determine the output voltage if it has 200 turns.
Please solve these questions below
A 50Hz, single phase transformer has a ratio of N2:N1 = 0.2. On full-load, the secondary current is 200A. The resistance and reactance of the primary winding are 0.8 ohm and 4 ohm respectively. The corresponding values for the secondary winding are 0.04 ohm and 0.1 ohm. If the secondary is short circuited, what voltage must be applied to the primary to produce full-load current? What will be the copper loss?
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 14.9-0-14.9 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, RL D2 32.63 21.07 42.14 O26.97