A binary to 8-segment display controller will be designed to guide patients based on2)their body temperature. If the patient body temperature is above or equal to 38°C, the displaywill indicate►, and it will displayotherwise. Block diagram of the complete systemis shown in Fig. 1. In order to turn on a segment the corresponding control output of thecontroller is set to logic-1.Fill in the truth table given in Fig. 2.а)b) The circuits for c0, cl and c4 will be implemented by using 8-to-1 MUXS andAND, OR, NOT gates. Draw the circuits for c0, c1 and c4.The circuits for c2, c3 and c6 will be implemented by using NAND gates. Drawc)the circuits for c2, c3 and c6.A BC D EF c0 cl c2 c3 c4 c51 0 00 0 010 0 0 0 11 0 0 0 101 0 0 0 1 11001 0 01 0 0 1 0 11 0 01 101001 1 11 0 1 00 01 0 1 0 0 1101 0 1 01 0 1 0 1 11 0 1 1 0 0101 1 |0 11 0 1 1 10101 1 |1 1c6 c7c5c6со с1 с2 с3 с4 с5 с6 с7Binary to 8-segmentcontroller† ↑ ↑ ↑ t ↑A B C D E FFigure 1Figure 2

Answered: Image /qna-images/answer/70351e94-c3b8-42e5-8d7b-044a33924e29.jpg

2) A binary to 8-segment display controller will be designed to guide patients based on their body temperature. If the patient body temperature is above or equal to 38°C, the display will indicate , and it will display - otherwise. Block diagram of the complete system is shown in Fig. 1. In order to turn on a segment the corresponding control output of the controller is set to logic-1. Fill in the truth table given in Fig. 2. а) The circuits for c0, c1 and c4 will be implemented by using 8-to-1 MUXS and AND, OR, NOT gates. Draw the circuits for c0, cl and c4. The circuits for c2, c3 and c6 will be implemented by using NAND gates. Draw c) the circuits for c2, c3 and c6.

2) A binary to 8-segment display controller will be designed to guide patients based on their body temperature. If the patient body temperature is above or equal to 38°C, the display will indicate , and it will display - otherwise. Block diagram of the complete system is shown in Fig. 1. In order to turn on a segment the corresponding control output of the controller is set to logic-1. Fill in the truth table given in Fig. 2. а) The circuits for c0, c1 and c4 will be implemented by using 8-to-1 MUXS and AND, OR, NOT gates. Draw the circuits for c0, cl and c4. The circuits for c2, c3 and c6 will be implemented by using NAND gates. Draw c) the circuits for c2, c3 and c6.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False
"Design a State Diagram and a schematic diagram of logic circuit of a Water Vending Machine. This machine works with 50 and 100 coins. It gives a water if at least 150 coins are inserted and no refund".
2- Which of the following instruction cannot be coded in 8086 assembly language ?give the reason why not if any. To verify your answer. code each instruction. a. MOV AX,27 b. MOV DX,77*3 c. MOV BX,23FB9 d. MOV BX,CS e. MOV CS,BH f. MOV DS,9BF2 g. MOV AX,DL
Solve the problem and simplify the output function using Quine–Mc Cluskey Methods. The following requirements must be met in solving the problem. Requirement:a. Truth Tableb. Timing Diagramc. Quine – Mc Cluskey Method d. Logic Diagram A private company wants to decide on a certain issue. Each of the four officials has an equal share of voting right. At least two of them must approve the solution in order to implement it. Each of them has a switch which closes to vote YES and open to vote NO.
Question No.3: Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “5410” should display on 7-seg Display and when user press 2 leds should glow 5 times in a loop. If any other key is pressed no action should be taken
A Karnaugh map is a of the logic system. O a. none of the above O b. Logical representation O c. data representation O d. graphical representation
logic circuitjust draw the graph
It's expected to construct one of the listed circuits and answer the relevant questions. 1. Design and implementation of combinational circuit using K-map and logic gate. 2. Design and analysis of combinational circuits as Adder & Subtractor / Multiplexer & De- multiplexer.
Sketch 3-input XOR/XNOR functions using DCVS (differential cascade voltage switch) and CPL (complimentary pass transistor logic), compare their speed, power, area, and explain your answers
Characteristics equation of logic diagram
QUESTION: DERIVE EXPRESSION VO IN TERMS OF THE INPUT VOLTACES V. HENCE SO THAT 4-BIT V₁ पैर AN A VALUE of LOGICO OUTPUT EA X₁₂ DELIVE THE INPUT VOLTACES V₁ V₁ AND VALY ES FOR THE CIRCUIT COMPONENTS THE CIRCUIT MAY BE USED AS A DIGITAL TO ANALOG CONFERTER. Assums 10ke For RE, LOGIC "'I' IS SVOUT] O VOLTS AND Full SCALE ANALOG IS IS VOLTS, STATE ANY ASSUMPTIONS MADE. Rf (₂ Ro FOR THE OUTPUT VOLTAGE IS SUMMING AMPLIFIER. Vo
1. Design a combination circuit and write a logic circuit when there are 3 switches and 1 lamp, the lamp will light when there are at least 2 switches per circuit.