1)for water at 14.696 psi & 100F, find v in ft3/lbm

Q: State three uses of the combination set

A: Combination set is an measuring tool, it is used to measure angles and lengths.

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: What is the value of w and y? y W 6V2

A:

Q: Says.003 is wrong

A:

Q: Question 1 The helical steel extension spring has a diameter of 2 inch, wire diameter of 0.1 inch,…

A: Given: diameter of the spring: D=2 inch diameter of the wire: d=0.1 inch for steel shear modulus:…

Q: 20 30 R15 5-Ø10 R10 Ø40 10 40 40 Figure 1

A:

Q: Using Combination set, The angle shown by the arc can be measured. hand written plzzz Select one:…

A:

Q: Sorry that's the wrong answer it is 0.62

A: Power coefficient = Cp=0.24 Wind speed = Vw=10.3 m/s Blade length = R = 34 m The power generated by…

Q: The figure shows a shaper machine that uses Whitworth quick return mechanism wherein the different…

A: Given Data OA=75cm OP=50cm CA=150cm CD=135 cm

Q: A drilling machine is to have 8 speeds ranging from 100 rev/min to 1000 rev/min. if the speeds from…

A: The total number of terms for this AP is: n=8 The first number is: a=100 rev/min The last number is:…

Q: A 2.10kg pole is attached to a wall with a hinge as shown. A 5.80kg sign is suspended at the other…

A: Given data: mp=2.10 kgM=5.8 kgD1=1.3 mD2=3.2 mα=19.0° Need to determine the torque on the pole due…

Q: In a lathe machine tool, when the cutting tool moves parallel to the axis of rotation of the…

A: It is required to justify given statement

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: 200 m The spool has a mass of 40 kg and a radius of gyration of k-0.65 m. If the 20 kg weight is…

A:

Q: Two identical cylinders methods cant be used to measure The hand writt Select one: True O False 4

A: Yes, it's true.

Q: For the following five questions put it in the true or false box. 1. The greater the difference in…

A: 1. The greater the difference in pressure between two points, the greater the flow rate between the…

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: Answer in 4-10

A: Given: →h1=3387.31 KJ/Kg→h2'=3074.5 KJ/Kg→h3=3457.04 KJ/Kg→h4'=3109.82 KJ/Kg→h5'=2384.82…

Q: 0 = 0° A

A:

Q: Which machine would you recommend given the following information and interest rate is 10%? New Used…

A: Given data as per the question  Interest rate = 10% Calculations considering 1st machineInital cost…

Q: Respond with TRUE if the symbol of the valve showll 4 2.

A: The symbol of valve is given

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: Find the value of x5 in 1 decimal places (positive value) using Newton-Raphson Method f(x) = 2x2 + x…

A:

Q: Given the force in spring AD (150N), final length of spring EC (0.8m), spring constant k = 9 N/cm,…

A: As per give condition,  For solution refer below images.

Q: At a certain instant, the particle of mass m has the position and velocity shown in the figure, and…

A:

Q: This answer was marked incorrect

A: The power input to the pump is 0.454 kW.