please answer the question in the photo with complete solutionAnalysis of frames/Zero force identification The frame shown is loadedby a 180-lb force appliedto member AE.the force at pin A, thereaction at support B, andthe contact force at rollerC. Note that there is nofriction at rollers C and180 1bDetermine4, in.2 in.4 in. 4 in. 2 in. 2 in.D.ReactionValue(left,right,upward/downwardABxByD.

for the given frame To determine (i) Forces at pin A (ii) reactions at support B (iii) contact…

180 1b The frame shown is loaded by a 180-lb force applied to member AE. Determine in. the force at pin A, the reaction at support B, and the contact force at roller C. Note that there is no friction at rollers C and 2 in. 4 in. 4 in. 2 in. 2 in. D. Reaction Value(left,right,upward/downward A By By D

180 1b The frame shown is loaded by a 180-lb force applied to member AE. Determine in. the force at pin A, the reaction at support B, and the contact force at roller C. Note that there is no friction at rollers C and 2 in. 4 in. 4 in. 2 in. 2 in. D. Reaction Value(left,right,upward/downward A By By D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The frame shown is loaded by a 180-1b force applied to member AE. Determine the force at pin A, the reaction at support B, and the contact force at roller C. Note that there is no friction at rollers C and D. E 180 lb 4 in. 2 in. Value (left, right, upward/downward Reaction 4 in. 4 in. 2 in. 2 in. A BX BY D
The T-bar AEBF is connected to rod CD, with the joint at F being equivalent to a slider bearing. The supports at A and C are slider bearings, and thrust bearings are found at B and D. The two applied forces, which act at the midpoint of the arm EF, are parallel to the y- and z-axes, respectively. Neglecting the weights of the members, draw the FBDs for the entire structure, the T-bar, and rod CD. Determine the total number of unknowns.
determine the magnitude of the vertical reaction force at pin D also. only HANDWRITTEN answer needed ( NOT TYPED)
Using the method of Joints. Find the forces in each frame member.
Problem 1 For the frame loaded as shown, determine all the forces on members AD and ABC. Support at C is a roller. Hint: Please be careful in this problem: at point A, there are three elements connected at A: a pin A that is connected to ground (so, two support reactions due to that, say Ax and Ay), then, bar AD (two more reactions at A due to bar AD: call these as Ax_prime, and Ay_prime) and the bar AC (two more reactions at A due to bar AC: call these as Ax_doubleprime, Ay_doubleprime). So, you will need to draw a pin FBD at A showing all the six forces. 200 N 130 mm 400 mm V400 N A B -400 mm 400 mm
The pulley at D is frictionless and the cylinder weighs 180 Ib. a. Determine the vertical reaction (Ib) of the hinge. Indicate its direction, use positive value if it is upward and negative if it's downward. b. Determine the horizontal reaction (Ib) of the hinge. Indicate its direction, use positive value if it's to the right and negative if it's to the left. c. Determine the tensile force (Ib) on the cable. A B C 5 ft 5 ft -3 ft
- 2. From the loading as shown, at what is fastened bya frictionless pin to a block weighing l0okN as shown in will produce a rotational equilibrium! figure. At vertical wall the Muau= 0.269 while under the block the Mblock= 0.20. Oetermine the force Pneeded to start the moti on to the Exercise No 3 Lab. A uniform bar AB weighing 5OOKN, distance (x) from the left support what are the values of R, and Rz? 4m 2m right. WAFICO KN W500KM bar X=?. 18 KN P: 18KN/M e = 45° A Molock= 0.2 E. 'k block C m FNA 3m RI Rz
Problem 2: Solve for the reactions at roller A and pin G. Solve for the force members: IJ, DJ, DE. 3kps 3kips 9' G B E Gspens @ 12'
ab 32 4 in 8 in 44R The assembly shown has the dinensions given above. When a force of F 220 ib is applied, find the tension in the rope, and the force that body CDEG exerts on body ABC at point C. Note: The distance AG is delberately not provided Forces: T 541.6717557b Fe 118 6095643/b(Denote a nghtward force with a positive value, a leftward force with a negative vale
Calculate the force in member GH of the truss and indicate whether it is in tension or compression, using either method of joints or method of sections. Required: Draw the FBD(s) as needed for analysis-all equilibrium equations must correspond to a FBD that you have drawn. Make sure to clearly indicate which FBD your equation(s) correspond to. K J H 4 ft C - 3 ft 3 ft -- 3 ft- 3 ft-3 ft 1500 lb 1500 lb 1500 lb 1500 lb 1500 lb
Find the horizontal and vertical reactions at the pin at B. Note that the support at D is fixed. Sign convention for the positive x and y direction applies for the answers. Diagram not to scale Answers: (a) -4 kN, 2 kN (b) 4 kN, -2 kN (c) 1.5 kN, 3 kN (d) -1.5 kN, -3 kN 3 kN B A D TTT 2 m 4 kN 2 m C 1m 2 m 5 m
Find the force in member BC?