160 0.5 H Vo 312.5 µF 4 V R=16 0, L- 0,5 H, C= 312,5 µF Vs(t) - 4 V Vc(t) = Vo(t). Constant voltage source voltage across capacitor current through the capacitor Voltage from inductance V(t) inductance current VR+ voltage across resistor current flowing through resistor Vc (0) 3V Capacitor voltage at time t-0 After the switch has been open long enough, it is closed at t = 0. Which of the following is the Laplace transform of the ic(t) current?

160 0.5 H Vo 312.5 µF 4 V R=16 0, L- 0,5 H, C= 312,5 µF Vs(t) - 4 V Vc(t) = Vo(t). Constant voltage source voltage across capacitor current through the capacitor Voltage from inductance V(t) inductance current VR+ voltage across resistor current flowing through resistor Vc (0) 3V Capacitor voltage at time t-0 After the switch has been open long enough, it is closed at t = 0. Which of the following is the Laplace transform of the ic(t) current?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
In reference to the load, how are capacitors connected to help prevent voltage spikes and surges? Are capacitors connected in parallel or in series with the load?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
Q9. i) An inductance network with total inductance across A and B is 30mH is shown in Figure CI. L4 L2 = 40mH L6 = 40mH Leq-30mH L1= 20mH L5 50MH 100mH 30mH B. Figure C1 Estimate, inductance value, L4. [3]
An inductor and a resistor are in series with a sinewave voltage source. The frequency is set so that the inductive reactance is equal to the resistance. If the frequency is increased, then options: Voltage across the inductor= Source Voltage Voltage across the inductor> Voltage across the resistor Voltage across the inductor= Voltage across the resistor Voltage across the resistor > Voltage across the inductor
Figure 2 shows three "LC" circuits, two of them with capacitors of capacitance "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitors "Cc" capacitors. inductance "L", the three circuits are coupled by means of two capacitors of capacitance "Cc". The currents circulating through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = -dQ/dt, find the system of coupled equations of the system and then find the angular normal frequencies of the system.
a)For the inductive element of Figure 1 , the current in phasor form is B) the voltage in phasor form for figure 1 is C)the impedance of the inductor for figure 1 is
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor?
The picture shows three LC circuits, two of them with capacitors of capacitance C and the three with coils of inductance L, the three circuits are coupled by means of two capacitors Cc capacitors.L inductance coils, the three circuits are coupled by means of two capacitors of capacitance Cc. The currentscirculating through each mesh are those indicated in the figure: I1, I2 and I3. Using Kirchhoff's law for voltagesand taking into account the definition of current I = -dQ/dt, find the system of coupled equations for the systemand then find the angular normal frequencies of the system.
Calculate values of asked physical quantities of the circuit in the figure. What is the capacitance of system 23? C23 C₁ = 3.0 F What is the capacitance of system 123? C123 = F C₁ = 2.0 F What is the capacitance of system 45? C45 = F Your last answer was interpreted as follows: 1 Your last answer was interpreted as follows: 1 What is the charge in the capacitor system? C Your last answer was interpreted as follows: 1 What is the total capacitance of the system? F Value 8.8500 x 10 EO Quantity permittivity of free space capacitance capacitance capacitance capacitance capacitance Your last answer was interpreted as follows: 1 capacitance of system 23 capacitance of system 123 capacitance of system 45 Your last answer was interpreted as follows: 1 Do not leave any fields blank. If you don't know the answer, insert 1 for example. Insert the answer with 3 significant digits without rounding the answer. Constant U = 7.0 V Unit E Symbol €0 C₁ = 3.0 F C1 C₂ C3 C4 C5 C23 C₂ = 9.0 F C₂ = 3.0 F…